0
It depends on what the vehicle is you are trying to replace one on. The hard part isn't changing the relay, it's getting to it. A lot of newer vehicles have them buried deep inside the dashboard and you literally have to remove the whole dash on some cars to get to it. Now, once you can get to it, it's no problem to change it. Just pull the bad one out of its socket and push in a new one. As long as the contacts on the new one match the old one you'll have no trouble with it. Just make sure you firmly push the relay into the socket so there's no chance of it wiggling loose or coming out altogether.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Where is the turn signal relay on a 98 Lincoln town car?
It is no longer a simple flasher relay. It is a signal module and it is located under the dash on the drivers side. It is a black plastic box aprox 3"wide by 4"long.
Can you switch the flasher for the blinkers with the emergency flasher relay?
Yes, as long as they have the same part number and many do.
Turn signal relay protege?
Turn signal/Flasher relay is under dash on drivers side, if you have a manual transmission is is almost directly above the clutch pedal. It is a gray colored box about 2 inches wide by 4 inches long. Just grab hold of it and pull it straight out of holder, should say flasher/turn signal on relay. FYI it can only be bought at the dealer! all auto part stores here in VA said it is a dealer item so imagine it is costly, i went to junk yard myself and got it for $7..Hope this helps.
Where is the relay flasher on a 2002 Ford 150 Super Crew?
I recently changed mine, be warned that it is not as simple a task as it is perceived to be. The turn signal relay flasher (or what I will be refering to as the "Flasher") is located in a black box, approx. 3 inches long, 2 inches wide, and 2.5 inches deep. This small box can be found under the dash on the driver side. To locate it, simple aim yourself between the accelerator and brake pedals, and look up. If the flasher is original, the box will be taped. Remove the tape and the clasps on each side of this box and inside will be your flasher as well as an accessory relay. The flasher is larger and closer to the passenger side than the relay, and mine was blue. It is a tight fit. 15 minutes and 2 pulled muscles to install a six dollar part. Best of luck.
When to replace a flasher relay for a Nissan Maxima?
Usually they last a long time. The only exception would be the ones that are thermal. Also if you are unhappy with the speed a new relay can change it. they just plug into fuse box. Don't fix if it isn't broken-there is no regular interval for changes.
Where is the turn signal relay on a 1986 Honda prelude?
The turn signal/hazard light relay is directly behind the fuse box. its about an 1 1/2" wide and about 2" long and its black.
Where is the flasher turn signal relay located on a 1996 Lincoln Town Car?
On the bottom of the steering column there are 3 Phillips screws. When your looking at the steering wheel the flasher will be on the left hand side. My flashers quit working and I jiggled it around, they started working, so I blew some compressed air into the plug and no more problems. Hope this helps.
Exactly how do you get to the mechanical turn signal flasher location on a 1997 GMC Jimmy Truck and what tools do you need and how do you get total access to it under the dash to replace it?
The light is made to flash with a plug-in flasher which is about an inch in diameter and and about an inch long. I should be located around the steering column about a foot from the floor. The actual turn signal device is located under the steering wheel. You must use a steering wheel puller to get to it.
Where is the turn signal flasher on a 96 S10 extcab?
The turn signal and hazard flasher are located slightly to the left of the cigarette lighter behind the kick panel. Remove the two screws visible on the long kick panel that extends under the steering wheel to the cigarette lighter. Pull out the ash tray and remove one small hex head bolt (7mm). Carefully pull the panel down and look straight in, on the left side of the cigarette lighter. The flasher on the left is the hazard flasher. The turn signal flasher is on the right (it is part #552 about $3 in the parts store hanging in the aisles). A pair of regular slip joint pliers opened up to their wide setting is very helpful in pulling it out. You don't get much room but you can install the new one fairly easily. Replace the 3 screws and you are finished. The flashers are hidden well and this is the easiest way I could find to replace it. You cannot reach it otherwise.
Where is the turn signal flasher on a 2003 Jeep Grand Cherokee?
The flasher is under the steering column. It is a little black box (relay switch about 3") long. You can only get to it by first removing the knee board under the steering wheel. Then if you reach up into the dash, to the right of the fuse box you can see the part you need. Mine has gone out and the blinkers quit working. Easy fix if you can find the part.
May 2005 f-150 turn signal blinks fast replaced bulbs are good?
Turn Signal Flash Rate DeterminationFirst here is a primer on how the flashing of turn signals is caused/controlled.Almost all vehicular turn signal flashing is controlled by a special relay commonly called a flasher.Inside the flasher relay is a self-actuating switch in which one of the two contact points is mounted on the end of a "bimetallic" [made of two dissimilar metal layers bonded together] strip of metal.As electric current [measure in Amps (A), or milliamps (mA], flows through the bimetallic strip, the current flow causes the strip to warm up.The two metal layers in the strip have different "coefficients of thermal expansion" resulting in one side of the strip lengthening faster than the other.By design, that causes the strip to bend from the heat, which results in the one contact on the strip being moved away from the fixed contact, and thus opening the switch.This turns off the current to the turn signal circuit and lamp [bulb], thus turning it off.As the bimetallic strip cools down slightly, it bends back to where it started, thus closing the contacts, energizing the circuit, and causing the turn signal lamp filament to turn ON.As long as the turn signal control switch on the steering column is closed, the signal flasher relay will continue to cycleopen and closed.Now to get to the basic original question as to why a turn signal will blink faster, or slower.The answer is that the rate of the flasher cycle is directly proportional to the amount of current [Amp or milliamps] flowing through the circuit.The amount of current is caused by the size and conductivity of the filaments in the lamps, and/or the number of lamps in the circuit. The larger the lamp filament the greater the current and thus the flash rate.The more lamps, the more current flows, thus heating the bimetallic strip faster, and causing it to open, turning off the lamps.One of the best examples of this is that when a trailer [with turn signal lamps] is added to the turn signal circuit, the flash rate will usually increase, unless the flasher is rated "heavy duty."For those whose cars and trucks have ordinary flasher relays and who don't like the rapid flash rate resulting with the addition of a trailer, they can replace the standard flasher relay occasionally referred to as a flasher "module" with a heavy duty one.
How long does it take to replace constant control relay module?
couple hours at most, not very hard!
