0
How many bolts are on a water pump in a Chrysler lhs 1997 3.5l if you need any more information just ask really need help to fix my mom's car but can't figure out how many bolt's for the water pump?
Wiki User
∙ 10y ago
This is actually one of the most difficult water pumps to remove in any vehicle. You will need access to the front of the engine which will mean taking out the radiator and shroud. You need to remove the main crank pulley and then the cover behind it. -You need quite a few special tools to do this .
Definitely NOT a job for an amateur.
The only way to know if it is a three or six bolt is to remove the timing cover and look.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How hard is it to replace the rear sway bars and links?
Not hard at all. 6 bolts for the sway bar, and depending on how many links 8 bolts if it is a 4 link, figure 2 bolts per link. ues jack stands to hold the rear axel in place and do it one link at a time. The sway bar cones off in one piece so do that last.
How do you anodize machine bolts to black color?
i am sure you could find out somewhere on the web, but would be easier to just buy anodized bolts or take em to a company that does anodizing
How do you change the thermostat on a 1999 Chrysler Concorde?
You should have the 5.2 engine with your Limited, but some have been ordered with the 4.0. The Thermostat is located on the front of the engine at the end of the Radiator hose. It is between the Alternator, and the A/C Compressor. You might find it easier to remove the Alternator to get to the 2 bolts that hold in the Thermostat Housing. remove them, clean the housing and the surface it sits on, install a new gasket and thermostat and put back anything else you may have taken apart.
Where is 2000 Chrysler Concorde starter?
== == 2.7 Liter V6 Engine.. On The Drivers Side Look Under The Engine.. Its Easily Accessed By Removing The Drivers Side Front Tire.. There Are 3 10mm Bolts On It And 2 Connection Wires To The Engine..
2001 Chrysler Concorde how to take off intake?
Remove the air intake hose from the Concorde. Take off the throttle cables and any fuel lines or vacuum hoses in the way. remove the bolts for the intake, then lift it straight up to remove it.
How do you remove the center console from a 2007 Chrysler Sebring?
The center counsel on a 2007 Chrysler Sebring can be removed by loosening the bolts on the bottom of the Council. The bolts are located at the back of the Council.
Where can you get the 3 star bolts or better bolt head option that attach to the back of the hub assembly on a 1996 Chrysler Sebring Convertible 2.5L?
The bolts can be purchased from your local Chrysler dealer.
How do you remove the evaporator on a 1998 Chrysler town and country?
97 Chrysler town & country evaporator bolts location for removal
How many bolts hold on an alternator on a 2001 Chrysler Town and Country?
Three.
Where is bell housing 1994 chrysler New Yorker?
It is the part of the transmission case that bolts to the engine.It is the part of the transmission case that bolts to the engine.
How do you remove the radiator on a 2005 Chrysler 300C?
Remove bolts, connectors and hoses. Replace. Hook up hoses, conectors and replace bolts. That easy!
Are there bolts holding down the battery on a Chrysler New Yorker?
Yes, there is a battery hold down.
Where can you find oem bolts for 1997 Chrysler LHS?
The dealership parts department should have them available.
How many bolts does a 1987 Chrysler 5th ave have on the rim?
its a five lug so 5
Where are the bolts on the starter 2002 Chrysler voyager?
They go through the transmission bell housing from the driver side.
Where are the bolts that hold the bumper in place on a 1998 Chrysler Concorde?
The bumpers on most newer cars are held on with two bolts on each side on the top of the frame in the engine compartment.
How do you change thermostat in Chrysler 300?
The thermostat in the Chrysler 300 is located beneath the alternator and oil tube, right under where the radiator hose hooks to the engine. To change it out, remove the three bolts from the housing on the old unit. Remove it, replace it with a new one and tighten the three bolts.
