Chevy Blazer
Chevy Silverado
Cadillac Eldorado

How many knock sensors on a 1997 Cadillac eldorado and where are they located?

414243

Top Answer
User Avatar
Wiki User
2005-10-13 03:15:24
2005-10-13 03:15:24

One Sensor.... Removal Procedure 1. Remove the intake manifold. 2. Disconnect the knock sensor electrical connector. 3. Remove the knock sensor. Installation Procedure 1. Install the knock sensor. Tighten the knock sensor to 19 Nm (14 lb ft). 2. Connect the knock sensor electrical connector. 3. Reinstall the intake manifold.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

the knock sensor on a 95 eldorado is located underneath the passenger side right above the trans-axel by the vss switch on the back of the motor, if its knot there its underneath the manifold.

User Avatar

the knock sensors are located in the top of the engine block. The intake has to be removed to get to the sensors.

User Avatar

knock sensors on a 2005 silverado are located under the intake manifold

User Avatar

There are 2 knock sensors and they are both located under the intake on the top of the engine. You must remove the intake manifold to access the sensors.

User Avatar

There are two knock sensors, they are both located under the upper intake manifold.

User Avatar

Underneath the intake manifold there will be two knock sensors

User Avatar

there are 2 knock sensors, they are located underneath the intake manifold

User Avatar

They are located down in the engine block valley. Accessing the knock sensors requires cylinder head removal..........sorry.

User Avatar

The knock sensors yes there are two are located on either side of the motor (4.3LTR Vortec) below the heads in the center area of the engine block. There are a place for another sensor just above where the knock sensor goes but these are for other sensors. The knock sensors yes there are two are located on either side of the motor (4.3LTR Vortec) below the heads in the center area of the engine block. There are a place for another sensor just above where the knock sensor goes but these are for other sensors.

User Avatar

The knock sensors are located under the intake manifold on top of the block. You have to remove the entire intake manifold to get to the knock sensors. Good luck, I am in the process of changing mine as well.

User Avatar

1993 Honda Civic EX's dont have knock sensors.

User Avatar

There are two knock sensors located in the block. They are just under the intake manifold.

User Avatar

There are 2 knock sensors on these motors. They are located in the valley cover under the intake manifold.

User Avatar

The knock sensor are located in the valley between the cylinder heads on V6 and V8 engines V8s have two knock sensors

User Avatar

There are two knock sensors on a 2001 Chevy 1500 with the 5.3 V8. You have to remove the intake manifold, because both of them are located under it. it is best to replace both knock sensors at one time, and you will need an intake manifold gasket too. There are two knock sensors on a 2001 Chevy 1500 with the 5.3 V8. You have to remove the intake manifold, because both of them are located under it. it is best to replace both knock sensors at one time, and you will need an intake manifold gasket too.

User Avatar

the knock sensors 1 and or front and back are locaded under the intake

User Avatar

Knock SensorEngine, Left Side6cly. Knock SensorKnock Sensors With Intake Manifold RemovedEngine, Top Center V8

User Avatar

There is 2 knock sensors on that engine and both of them are underneith the intake manifold. You MUST remove the intake to get to them, no other way.

User Avatar

That engine has 2 knock sensors and there both underneith the intake manifold. You must remove the intake to service them.

User Avatar

The knock sensors are located underneath the intake. There are actually two knock sensors one front (KS1) and one in rear (KS2).

User Avatar

faceing the eng. op your right below the exsust man

User Avatar

Under the intake manifold, sucks but enjoy!

User Avatar

Sienna's have two knock sensors located in the valley underneath the intake manifold. Replacement is a three hour job.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.