0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How many turns out on the fuel screw on a 1992 Honda nighthawk 250?
two and half turns (so it is 5half turns)
How many turns do you start at to find the correct fuel and air mixture on a 750 Edelbrock carb?
Here's a general rule of thumb: Close the fuel mixture valve, then back it out 2 1/2 turns. Then adjust it from there. It's a good starting point, and usually works for me.
How many turns to set fuel air mixture settings on a 1995 Yamaha timberwolf 250?
Turn it all the way in and then back out 1 1/2 turns
How do you adjust carburetor on a 80 cc Yamaha badger 4 wheeler?
On the left side of the carb there are two screws, a recessed brass screw with slotted head (mixture adjustment screw) & a silver-colored screw with a Phillips head (idle adjustment screw). To properly tune the carb (assuming the carburetor body, jets, and bowl are clean & there are no air leaks) turn the idle screw (silver) clockwise to raise the idle...raise the idle quite a bit. Then, with the engine idling fast, turn the mixture adjustment screw (brass) in several turns (keep a count) and out several turns (again, it helps to keep track of how many turns) and listen for the moment when the engine runs the fastest. Now, with the mixture adjustment screw (brass) near the spot where the engine runs the fastest, turn it 1/2 turn either direction and listen for the spot where the engine seems to run the best, set your mixture adjustment screw (brass) to that spot. Then drop your idle back to normal by turning the idle screw (silver) counter-clockwise. Your carb is now tuned (simple...raise the idle, adjust the mixture for fastest/smoothest rpm, then lower your idle...done).
If a screw moves one inch in 12 turns how many inches will it move in 30 turns?
2.5 inches
How many turns on carburetor idle screw for 1999 yz 125?
Carb. idle screws are set so thew vehicle idles they are not set at a specific number of turns. With the screw turned out but still in the carb start the vehicle. Let it warm up then turn the screw in until the engine will just idle. There are other adjustments that may assist are to the pilot fuel/air screw. This should be screwed all the way in until it lightly bottoms then turned out 2 turns to start. Once the bike is idling per above turning this screw until it idles at the highest point. This should be between 2 and 3 turns out. Readjust the idle screw to the lower idle if needed and you will be ready to go.
How many times do you wind out the mixture screws to give you best fuel economy on a 350 holly?
The initial setting for the mixture screws is 1 1/2 turns out. Connect a vacuum gauge and turn them until you get the highest reading and make sure they are both set the same. This will give you the best fuel economy.
How many out turns to adjust the idle screw of a rears chainsaw model358.360380?
The pointed end of the idle speed screw should be centered on the idle arm on the carburetor. http://store.chainsawr.com/
What is the chemical symbol for fuel?
A fuel is a complex mixture of many components; no chemical symbol.For methane gas the chemical formula is CH4.
How many turns out on the high low fuel mix to get a 2.0 chain saw to start?
Start with 1and1/2 turns out on both high and low
How many turns out should the pilot screws be on a 1983 Yamaha Virago 750?
The optimal setting for a pilot screw on almost any bike is one and one half full turns out from the closed position.
How many ounces to the gallon of fuel mixture on 6 horsepower Johnson outboard 2 stroke?
If it is a 50 to 1 mixture it would be 2.6 ounces per gallon
