0
How should you remove the timing belt or camshaft on '99 Tacoma?
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
Must you remove the camshaft for timing gear replacement on a 1986 2.5 Chevy Celebrity?
Yes, you have to remove the camshaft from the engine to replace the timing gear. The timing gear is pressed both on and off of the camshaft using an arbor or other suitable press. Since there is not room to remove the camshaft in the car the engine has to be out of the car.
Must you remove the camshaft to replace the timing belt of a 1989 Chevy Celebrity 4-cylinder?
no The Chevy Celebrity 4 cylinder engine doesn't use a timing belt, it uses a timing gear. To replace the gear it is necessary to remove the camshaft from the engine as it is a press job. To remove the camshaft it is necessary to remove the engine from the car.
How do you find crank sensor on Toyota Tacoma?
Remove the lower timing belt cover and then the sensor should be to the right of the crankshaft pully.
Where is camshaft position sensor located on a 2000 Toyota Tacoma?
Under the left side cam under the timing belt cover
How do you change camshaft on a 2000 ford excort?
remove the valve cover,remove timing belt , lossing all caps that hold camshaft,then remove the caps, lift out the shaft.
When should you change timing belt on 1998 Toyota Tacoma?
How do you change a timing belt on a 1998 Toyota Tacoma? And what part do I need to buy?
When should you change the timing belt on your 2006 Tacoma?
Your 2006 Toyota Tacoma has a chain and not a belt. No maintenance is required.
How do you set the timing on a 1996 altima?
remove two piece oil pan and timing oil pump cover and line up the marks on the chain with the marks on the timing gears crankshaft and camshaft sprockets should show similiar in the book...
2000 Daewoo Leganza engine timing diagram?
what is the timing marks on the camshaft what is the timing marks on the camshaft
What are the timing marks for a 1997 Ford F150 4.6 liter engine?
{| |+ Special Service Tool(s) |- | Cam Positioning ToolT91P-6256-A Cam Positioning Tool AdaptersT92P-6256-A Camshaft Holding ToolT96T-6256-B Camshaft Positioning ToolT96T-6256-AR Removal # Remove the engine front cover; refer to the procedure in this section. # Remove the (A) crankshaft sensor ring from the (B)crankshaft (6303).# On WEP engines, use the (A) Camshaft Positioning Tool to position the (B) camshaft.# on REP engines, rotate the crankshaft until both camshaft keyways are 90° from the cam cover surface. On REP and WEP engines, make sure the copper links line up with the dots on the camshaft sprockets.# On REP equipped engines, install the (A) Cam Positioning Tool and the Camshaft Positioning Tool Adapters on the (B) camshaft.# On WEP engines, install the (A) Camshaft Holding Tool on the (B) camshaft.# Remove the (A) LH timing chain tensioner bolts and the (B) LH timing chain tensioner.# Remove the (A) RH timing chain tensioner bolts and the (B) RH timing chain tensioner.# Remove the LH and RH timing chain tensioner guides from the dowel pins.# CAUTION: At no time, when the timing chains are removed and the cylinder heads are installed may the crankshaft or camshaft be rotated. Severe piston and valve damage will occur. Remove the RH and LH timing chains and crankshaft sprockets. ## Lift RH timing chain off of the camshaft sprocket and slide the timing chain and crankshaft sprocket off of the crankshaft. ## Lift the LH timing chain off the camshaft sprocket and slide the timing chain and the crankshaft sprocket off of the crankshaft.# On REP engines, remove the chain guides. ## Remove the LH timing chain guide bolts. ## Remove the LH timing chain guide. ## Remove the RH timing chain guide bolts. ## Remove the RH timing chain guide.# On WEP engines, remove the chain guides. ## Remove the LH timing chain guide bolts. ## Remove the LH timing chain guide. ## Remove the RH timing chain guide bolts. ## Remove the RH timing chain guide.Installation CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result. # Compress the timing chain tensioners (6L266). ## Release the lock assembly on the timing chain tensioners. ## Compress the timing chain tensioners.# Install the retaining pins.# Check the following components for part number orientation.! valign="bottom" | Item ! valign="bottom" | Part Number ! valign="bottom" | Description | 1 6268 Timing Chain/Belt (RH) 2 - RH Timing Chain Guide (WEP) 3 6L253 Timing Chain Tensioner Arm (LH) 4 6L266 Timing Chain Tensioner (LH) 5 6268 Timing Chain/Belt (LH) 6 - LH Timing Chain Guide (WEP) 7 6K297 Timing Chain Guide, (REP) RH 8 6L253 Timing Chain Tensioner Arm (RH) 9 6L266 Timing Chain Tensioner (RH) 10 6K297 Timing Chain Guide, (REP) RH# On REP engines, install the timing chain guides. ## Position LH timing chain guide. ## Install and torque the LH timing chain guide bolts. ## Position the RH timing chain guide. ## Install and torque the RH timing chain guide bolts.# On WEP engines, install the timing chain guides. ## Position the LH timing chain guide. ## Install and torque the LH timing chain guide bolts. ## Position the RH timing chain guide. ## Install and torque the RH timing chain guide bolts.# Install the timing chain/belts (6268) and crankshaft sprockets (6306). ## Slide the (A)crankshaft sprocket onto the (B) crankshaft, aligning the copper link on the timing chain/belt with the dot on the crankshaft sprocket. ## Position thetiming chain/belt over the camshaft sprocket, aligning the copper link with the dot on the camshaft sprocket.# Make sure that the (A) copper marks on the timing chain/belts are lined up with the corresponding dots on the crankshaft and camshaft sprockets.# Make sure that the (A) camshaft sprocket keyway is 90° from the (B) cam cover mounting surface.# Make sure that the (A) RH timing chain sprocket is on the front of the (B) LH timing chain sprocket with the hubs facing each other.# Position the LH and RH timing chain tensioner guides on the dowel pins.# Position the RH timing chain tensioner and install the timing chain tensioner bolts.# Position the LH timing chain tensioner and install the timing chain tensioner bolts.# Remove both the RH and LH retaining pins from the timing chain tensioners.# On REP engines, remove (A) Cam Positioning Tool and the Camshaft Positioning Tool Adapters on the (B) camshaft (6250).# On WEP engines, remove the (A) Camshaft Holding Tool from the (B) camshaft.# On WEP engines, remove the (A) camshaft positioning tool from the (B) camshaft.# Install the (A) crankshaft sensor ring on the (B) crankshaft.# Install the engine front cover; refer to the procedure in this section. |}
Why will a car turn over but not start in your volvo97 850?
Assuming there is fuel and spark to the proper components, then check the timing belt for slipping or broken. Remove the oil fill cap, and have someone crank the engine while you look at the camshaft. The camshaft should turn, if not, most likely the timing belt is defective.
How do you install 2000 galant timing belt?
Remove the drive belts, crankshaft pulley, and timing covers. Align the timing marks on the camshaft and crankshaft and r+r the belt
