Peugeot
How To

How to Adjust clutch pedal height peugeot 307?

123

Top Answer
User Avatar
Wiki User
Answered
2014-05-23 20:36:06
2014-05-23 20:36:06

To adjust the clutch pedal height in the Peugeot 307 locate the adjuster bolt on the floor under the clutch pedal. Loosen the bolt and pull out the pedal to the proper height then tighten the bolt. To make the clutch pedal lower for the operator simply push in on the clutch pedal while the adjuster bolt is loose, then tighten the bolt.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


Hi, if you look at the pedal, there is a 10mm bolt, adjust it out to make the pedal higher, or adjust it in to make the pedal lower.


The clutch pedal can be adjusted for height. There is no adjustment for the actual clutch on a 2000 Accent.


You can only adjust the clutch pedal. You can adjust position and range just on top of the pedal.


The clutch itself cannot be adjusted in any car that I know of, what is adjustable is the clutch pedal. In 95 Accents you can adjust the pedal height by losening the nut that holds the rod that connects the pedal to the clutch cylinder, then you just have to give it a few turns until the desired pedal height is achieved. Don't forget to re-tighten the nut again and you are done.


The clutch pedal cannot be adjusted


how to adjust a 95 dodge neon clutch? how to adjust a 95 dodge neon clutch?


To adjust the clutch pedal on a Saab the clutch line needs to be bled. Bleeding the clutch line will allow any air to escape and stiffen up the pedal.


where does the clutch cable go from the pedal?? my clutch snapped earlier


where and how to adjust clutch pedal 1993 s10 It is hydraulic operated, there is no adjustment.


Fault with clutch master cylinder.


It could possibly be your clutch pedal height. I had to fix the problem in my car, had the same thing happening. Go to your local shop or look up on the interweb and find out how to adjust the clutch pedal height.


No.The clutch is hydraulic and not adjustable.


If it's a cable clutch i believe you can only adjust the position of the pedal, not the moment that the clutch engages. But I could be mistaken


the clutch on a 2000 ford f250 is a hydraulic clutch there is no adjustment however check the bushing on the rod and pin on the clutch pedal this bushing wears out and you loose pedal if the pin is wrn ,you will have to replace the clutch pedal


At the top of the clutch pedal in the cab of the truck.


depress the clutch pedal to the floor several times


look under the dash at the top of your clutch pedal ;)



You can tell by how much higher the clutch pedal is to the brake pedal. when new pedals are at the same height.


There is a rod that runs from the clutch pedal mechanism to the clutch fork. On this rod there should be threads and a couple of nuts to adjust the length of the rod shorter or longer. Adjust as needed.


Inspect the condition of clutch pedal rubber stop, if damaged or missing install a new one. Where necessary, disconnect interlock clutch rod at transmission end. Adjust clutch linkage by turning self-locking adjustment nut to provide 5/32" free movement at outer end of clutch fork. This adjustment will provide the required one inch free play at the pedal. Reassemble interlock rod if used.


On a 1996 Ford Mustang : To adjust the clutch : - without the engine running , put your transmission in 1st gear - GENTLY , with your foot , pull the clutch pedal UP until it stops moving - SLOWLY push the clutch pedal DOWN all the way ( if you hear a click the clutch needed adjusting and has adjusted itself )


You may need to adjust your clutch or replace your clutch.


The adjustment is made on the clutch cable, near where it connects to the tranny.




Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.