0
On the stereo faceplate there are 4 holes near the four corners of the unit,there is a special tool that fits in there to remove them.
Basically the tool uses a straight section of wire poked in the hole to remove the spring loaded tab from behind the edge that holds the stereo in.
Four lengths of wire or 4 small screwdrivers in the holes approxiamely 6-8cm will wensure the tabs are unlocked and the stereo should just then pull out.
Ensure you have put the screw drivers in far enough as you wont need to force it to get it out.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you remove the stereo from a 2008 Mazda 6?
Remove the decorative stereo cover. Remove the stereo retaining screws. Pull the stereo out and remove the wiring harness and the antenna cable.
How do you replace the factory stereo on a 1998 Mazda 626?
http://www.mazda626.net/index.php?showtopic=28489
How do you remove the stock stereo from a 1990 Mazda Protege?
screwdriver, and then pull hard enough to rip out the wires and then there you have it. the way to remove a stock stereo the theft version
How to install CD player in 2001 Mazda Protege?
How to uninstall your factory/or aftermarket stereo in the 2001 Mazda Protege: first you will need a Radio Removal tool. You can buy this at any parts store. you can remove the cover around the stereo, but that is not necessary - you can just pull the stereo out with this dashboard cover in place. remove the vertical tab edges on your car stereo (if it is the factory stereo that came with the Protege) after these are removed, (you can use the tool you just bought to gently pry off the edges), then you will see the holes to insert the removal tool into. Press the tool ends into the holes on both sides, until you hear them click. It's probably about 1 inch deep. Then, pull on both tool edges, the stereo will just pop out then. unplug the stereo, and connect your new stereo. Push the new stereo system back into the slot making sure it's back in as snugly as the other one. You're done. (you may need an insert, or wiring harness depending on the type of stereo you are putting back in. you can buy these were you buy your stereo.)
Mazda e2000 wiring for stereo?
Able stereo wiring diagram, for your Mazda, can be obtained from most Mazda dealerships. The wiring diagram will make wiring your stereo much easier.
Is there a stereo wiring diagram for 2008 Mazda 6?
i need stereo wiring schematic for 08 mazda 6 non-bose
Wiring stereo 99 Mazda truck?
The 1999 monster truck stereo wiring diagram can be obtained from most Mazda dealerships. The stereo has a wiring harness consisting of five wires.
Which wire in a 1999 Mazda b2500 with a factory stereo and harness is the remote wire for external amps?
No remote wire on stock deck tap into igniton wire (yellow with black stripe) for 1999 ford rangers & Mazda B-series.
What is the colour coding in a Mazda astina for stereo?
Seven.
What are some the standard factory colors for a Mazda pickup?
One of the standard factory colors for a Mazda pickup is the color white. Another of the standard factory colors for a Mazda pickup is the color dark grey.
How do you remove a stock stereo from a 2000 Mazda Mellenia s?
Remove the plastic trim panels to the left and right of the stereo with your fingernails or something that will not scratch the plastic. This will reveal four holes on each side. At a Radioshack type store you can buy DIN removal tools. But for a Double Din stereo you will need to buy two such packages. The instructions come with the package.
What can you try after installing a new stereo in a 1999 Mazda that has no matching illumination wires from the stereo for the wires in the car and now the dash lights not to work?
Ive installed some aftermarket decks in late model mazda's , try wiring your own ground to get the dash lights back... seems the wire that the factory deck grounded with acts as a relay or something with a negative signal running through it
