answersLogoWhite

0

Brake Pads and Rotors
Dodge Ram
How To

How to remove rotors on a 99 dodge 2500?


Top Answer
User Avatar
Wiki User
Answered 2005-10-23 01:56:13

I only know that my mechanic had to beat the old ones to a pulp to remove them. He said they get stuck sometimes and don't slide off like they should.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

How do install rotors on 99 Dodge Durango?

Remove the tire and wheel. Remove the brake pads and hardware. The rotor will slide off. Reverse the process to install the new rotors.


Where is the fuel pump inertia switch on 99 dodge 2500?

There is none.


Are the body size the same for a 99 dodge 1500 and 2500?

The body (cab), yes.


Headlight wiring diagram for 99 ram 2500?

i have a 99 dodge sport ram 2500 passenger side headlight is not bright and the two in side lights dont come on at all why?


What front seats can a 1999 dodge ram 2500 interchange with?

Just about any 94 to 99


Can you swap 95 dodge 2500 transmission with a 99 dodge 2500?

Manual, yes.Automatic, no. The control systems are differentManual, yes.Automatic, no. The control systems are different


Will ford super duty rims fit on a dodge 2500?

NO, the dodge is 8 on 6.5 bolt circle while ford, in 99, switched to 8 on 170mm bolt pattern. Superduty started in 99 so all was metric.


How much oil does a 99 dodge 2500 need?

5 quarts if a v8 7 quarts if a v10 12 quarts if a diesel


Will brake rotor on 99' Dodge Ram van 1500 fit 98' Dodge Ram van 1500?

Yes, if it's the same model (1500, 2500, etc.).


What is the sum of odd numbers 1-99?

100


What is the horsepower of 99 dodge ram 2500 24v cummins?

235 hp @ 2700 RPM, 460 ft lbs torque @ 1400 RPM


How much can I expect to spend to have someone replace the rotors on a 99 Pontiac Grand Am?

On a 99 Pontiac Grand Am, you can expect to spend up to 500.00 on replacing your rotors, this is because the 99 used different rotors than the rest of the series. To replace rotors on your 99 Grand Am, you can expect to pay around $150. Take it yo your local NTB or brake store to get the work done, You can also take it to the dealership.


How to replace rotors on a 98 Kia Sephia?

You can replace these rotors rather easily.I have a 99 Sephia and I also replaced the rotors,Purchase a 7 PC screwdriver bit socket set from sears to remove the set screws and that's it.Remove caliper bracket, set screws on rotor and rotor.


How do you get the axle nut off which way do you turn it on a 99 dodge dakota sport?

Turn counter clockwise to remove.


Wiper motor for a 99 dodge avenger?

How do I change a Wiper motor for a 99 dodge avenger?


How do you remove rear rotors on a 99' F250 4x4?

first you need a special tool to remove bearing nut on this vehicle then u need to tell if this vehicle has full floating or semi floating axles.


Where is the drain plug located for my transmission on my 99' Dodge Avenger ES?

There isn't one. You have to remove the pan to drain


How do you change transmission filter in 99 dodge ram?

remove pan, change filter, reinstall pan, fill fluid.


How do you change front rotors on 99 Nissan frontier?

you cant. the are superglued on!


How do you put in thermostat on 99 dodge caravan?

Follow the upper radiator hose to where it meets the engine. Remove the two bolts of the thermostat housing and remove and replace the thermostat.


What is the sum of all odd numbers to 99?

2500


What is 0.0396 as a fraction?

0.0396 as a fraction= 99/2500


How do you get the rotors off of a 99 2500 suburban 4x4?

They're held in with four large Allen head bolts behind the rotor for the 2500 series. I would highly recommend getting a Craftsmen Allen head socket set (MADE IN USA!). Also a breaker bar, they are on there with about 80 to 100 pounds of torque.


Where is the crank shaft sensor on 99 dodge cummins?

It is on the drivers side buried behind the starter. You need to remove the starter and then you have access to it.


Where is the fuel filter on a 99 dodge ram 2500 turbo diesel engine?

It is on the driver side of the motor bolted to the firewall it has 2 meatl lines with banjo fitting and a nut on the top of it