0
I have a 93 Nissan Sentra. The plug wires and distributor cap have been removed. How can I replace these correctly. I need a firing order and information on how to install the distributor cap.?
Billybarrett85
Add your answer:
Earn +20 pts
How do you install a distributor in a 1996 Yukon?
I removed the distributor in my 96 gmc yukon but I forgot to mark it before removing it.What do I need to do to get it back in.
How do you set the timig for 2002 Chevy silverado v6 after the distributor has been removed?
You must have an engine scanner to set the timing correctly.
Is there any other location you can install a oil pressure sensor then behind the distributor on a early 350?
There is usually a pipe plug above the oil filter that can be removed.
What is the proper timing degree for a long block 4.0 1993 Jeep Wrangler?
2.5L and 4.0L ENGINE NOT ROTATED 1. Clean the mounting area of the cylinder block and install a new distributor mounting gasket. On some models there is a fork on the distributor housing. The slot in the fork aligns with the distributor hold-down bolt hole in the engine block. The distributor is correctly installed when the rotor is correctly positioned and the slot is aligned with the hold-down bolt hole. On these computer controlled distributors, initial ignition timing is not adjustable. 2. Align the rotor tip with the scribe mark on the distributor housing during removal, then turn the rotor approximately 1/8 turn counterclockwise past the scribe mark. 3. Slide the distributor shaft down into the engine. It may be necessary to move the rotor and shaft slightly to engage the distributor shaft with the oil pump slot. Align the scribe mark on the distributor housing with the mark on the cylinder block. Ensure that the distributor is fully seated against the cylinder block. It may be necessary to slightly rotate (bump) the engine while applying light downward force to fully engage the distributor shaft with the oil pump drive gear shaft. 4. Install the distributor shaft hold-down and bolt. Tighten the bolt to 17 ft. lbs. (23 Nm). 5. Install distributor cap and ignition wires. Insure that the wires are routed correctly before attempting to start engine. ENGINE ROTATED 1. Rotate the engine until the No.1 piston is at TDC compression. 2. Using a flat-bladed screwdriver, in the distributor hole, rotate the oil pump gear so that the slot in the oil pump shaft is in the correct position (see illustration). 3. With the distributor cap removed, install the distributor so that the rotor is positioned correctly (see illustration). Insure that the distributor is fully seated against the cylinder block. If not, remove the distributor and perform the entire procedure again. 4. Tighten the hold-down bolt. 5. Install distributor cap and ignition wires. Insure that the wires are routed correctly before attempting to start engine.
How do you install an engine block heater on a 1990 Honda Accord EX?
I had to replace my block heater on my 89 Accord and the plug/location for the heater is in behind the distributor. I had to remove the distributor from the engine block and then removed the old block heater. It is an easy do it yourself job but you have to be carefull to reinstall the distributor exactly the same way it came out. .
How do you set the timing on a 1994 Pontiac sunbird 3.1 6cyc?
You don't. It has no distributor. The only thing to make sure of is that the timing chain is installed correctly....(if you've removed it) and that the plug wires are routed correctly. If it's running poorly you'll have to look at other reasons besides the timing.
Does the torque converter have to be removed to change out a transmissions on 2001 Chevy X Z?
It must be unbolted from the engine flex-plate (flywheel) then correctly installed into the replacement transmission. Failure to install the torque converter correctly will result in expensive damage to the transmission.
Can paint be removed by painters tape?
Not if it is applied correctly, and removed in a timely fashion.
Do you have to drop a gearbox on a 1.8i cavalier expression to do a clutch?
The transmission must be removed to install a new clutch.The transmission must be removed to install a new clutch.
In order to remove the intake manifold on a 1999 Chevrolet Suburban 5.7 do you have to loosen or remove the distributor?
Yes you do. The distributor must be removed.
Can a car operate correctly with catalytic converter removed?
No, it will not run correctly and it is also illegal to remove the converter.
Can't install a update onto my ps3?
I found that I could not install an update until after I removed a Game disk. No message was given the install just would not work and it did as soon as the disk was removed
