answersLogoWhite

0


Best Answer
Copy

If you can insert the key and turn it to the run position.then look under the steering column where the key is you will see a holein the plastic cover if you push the pin inside with a paper clip or pick of some sort then you should be able to pull the switch out. if you cant get to the pin then pull the lower cover from around the steering column where the switch is located it should have only (3) Phillips screws holding it.

User Avatar

Wiki User

โˆ™ 2011-09-12 21:33:56
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: If the ignition switch on a 1991 Ford Bronco broke how do you put in a new switch?
Write your answer...
Submit

Related Questions

How can you tell if the ignition switch is bad on a 1991 ford bronco full size?

well there was a recall on part of the switch o you might make sure that isn't the part


How do you replace an ignition switch for a 1977 Chevrolet truck?

n ignition switch on a 1991 Chevrolet astro vanAnswern ignition switch on a 1991 Chevrolet astro van


How do you remove and replace the ignition switch on a 1991 Mercury Sable?

The 1991 Mercury Sable ignition switch is held in place with a retaining ring. Loosen the retaining ring. Pull the ignition switch out. Remove the wiring harness from the rear of the ignition switch. Reverse the process to install the new ignition switch.


How do you install ignition switch on 1991 Mazda Navajo?

How to remove ignition switch on a 91 Mazda Navajo


How do you change the key cylinder of the ignition switch in a 1991 acura legend?

Remove the retaining ring at the top of your 1991 Acura Legend ignition switch. The ignition switch cylinder will slide out. Remove the wiring harness from the end of the ignition cylinder. Reverse the process to install your new ignition switch cylinder.


1991 Ford Bronco with a 5.3 liter engine When the ignition switch is turned to on and the 'coil wire' is off of the ignition module the coil module contact arcs continually Bad Module?

you don't have a 5.3L in the bronco. If it is indeed an Eddie Bauer then it should be a 5.8L, but other options include 5.0L and 4.9L.


How do you change a ignition switch on a 1991 cougar?

Ok so you have to go where the ignition switch is at on the 1991 cougar. Next, You have to take the old one out. Last, you have to put the new one in.


Is there a ignition kill switch on a 1991 Chrysler new yorker?

No.


How do you remove the ignition switch with out key on a 1991 Chrysler new yorker?

The entire ignition switch assembly will unholy from the steering column. The key is required to remove the cylinder from the switch.


How do you replace a ignition switch tumbler 1991 skylark?

how do you replace a ignitionswitch tumbler 1991 buick skylark


How do you replace the ignition switch on a 1991 Chevrolet Caprice Classic?

ignition switch is located on top of steering column you will need to drop column down to access it


1991 Honda Accord engine cuts out while driving?

Ignition switch


How do you change the ignition switch on a 1991 Pontiac grand am tilt steering automatic trans?

I don't know how to change the ignition switch but I have some advice. Don't screw with the ignition switch, buy the whole steering column. It will be cheaper and easier to change.


Where you can get the ignition switch for ford escort station wagon 1993?

Most major parts houses would have the ignition switch. Any year between 1991 and 1996 will fit it.


Where is the ignition starter switch located on a 1991 Ford Ranger?

on top of your steering collum.


How do you replace an ignition switch in a 1991 Volvo SE Turbo Wagon?

replace ign sw on 1991 volvo 240


How do you replace the ignition switch on a 1991 Ford F-150 pickup?

The ignition switch is usually mounted to the steering column and is operated by a linkage rod. NOTEOn column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch: * Remove the ignition switch wiring harness. * Unbolt it from its position. * Bolt the new switch into position. * Attach the witing harness.


Where is the ignition switch located on a 1991 oldesmobile silhouette?

right thar where you put the key in it. No, that is the key cylinder. The ignition switch is located on the steering wheel column below the insulator panels.


What causes ignition control module to fail repeatedly in 1991 Ford Bronco 302 FI?

http://www.therangerstation.com/tech_library/TFI_Diagnostic.html Heat


How do you change the ignition cylinder on a 1991 Cadillac Eldorado?

Remove steering wheel and signal switch


How do you remove an ignition switch that is jammed in the run position on a 1991 sunbird?

Never mind figured it out


Where is the ignition switch located 1991 camaro rs?

top of the steering column near the bottom.


Will a headlight from a 1992 Ford Bronco fit in a 1991 Bronco?

no it will not


Is there a switch to allow ignition on the clutch or clutch pedal of a 1991 ford bronco?

Probably so. Look under your dash and follow the clutch pedal with your eyes if possible- with your hands if not. It is a safety feature to keep vehicle from starting in gear. I have heard of them being bypassed.


1991 ford bronco Replaced starter and solenoid and it still won't turn over What is next?

Neutral Safety switch. or equivalent.