100 metres seems to be the length of a spool of gardeners cotton Discuss:How_long_is_a_piece_of_string...we are not talking about jute twine here!So the maximum length of a piece of string would be 999.99mm!So the real answer to 'how long is a piece of string?' would be...anything between 0.01mm to 999.99mm.
The shape is known as an involute the shape is analogous to unwinding a piece of string from a spool representing the base circle diameter of the gear, imagine your pencil at the end of the string and the string kept tight during unwinding, unwind until line meets OD of gear, then apply blend radius at base circle, then mirror about tooth centre line for full tooth profile.
To make a pulley, get a coat hanger. Cut the bottom of the hanger, and insert the open ends into an empty wooden spool. Adjust wire so spool turns easily, and then bend the ends so that the spool won't fall off. Hang rope on the spool. Attach one end of rope to a bucket or can. To use, hang the pulley and pull on the end with no bucket or can.
A bobbin or a Spool
its measn to have fun
A device for dividing the flow into the valve between two outlets. The spool is pressure balanced by the flow across it. When a greater pressure drop occurse at one of the ports the spool moves across to counteract this and divert more flow to one side. They are not perfectly accurate.
pull straight out to remove the spool, wind in the direction of the arrow - to replace, feed the string through the hole and pull on it, keeping slight tension on the spool as you push it back into the head
pop the spool out wind string in direction of arrow, replace
First release the spool from the reel. Then take a length of string and tie it to the spool use a small knot keep it tidy.You then wind the string onto the spool in a clockwise direction until it covers approx 1/8 of the capacity of the spool.You then attach the nylon fishing line or braid,to the string with a small tidy knot and try hiding the knot on the outer edge of the spool.You then lift up the bail arm of the reel and refit the spool and close the bail arm.You would then load your line onto the reel until 1-3mm from the top of the spool, Be sure to wind the lines reasonably tightly.
a spoolcase is something that you use in sewing or when you sew you put the spool into a spoolcase but you must make sure the spool is filled up with thread then you can start sewing only if you have a long piece of thread in the spool!!
The parcel was tied with string.I tied string across the room to hang all my Christmas cards on.How long is a piece of string.I wear a string vest, very sexy, not!
I have a Kawasaki KTR27A string trimmer and I am very disappointed that Kawasaki's Owner's Manual did not include instructions on how to put new string in their trimmer. The challenge was getting the spool out. I finally figured out that you need to depress the center bumper and turn it clockwise. It will move easily to a stop, then turn it just a little harder and you will feel it move a little more. That releases it and you can pull it straight out. Then, just wrap new string on (direction is indicated on the spool), feed the two ends out through the holes in the head, and put the spool back in making sure not to have any of the new string underneath the spool. Then depress the bumper and turn in counter-clockwise to set it in place.
3yd - 1 feet
It's tangled on the spool. You need to open & rewind around it.
It depends on the length and quality. Regular curling ribbon on a small spool is about $5, but 50-yards can get up to about $20.
Sometimes it is called a Dutchman or spool piece depending on which trade is using it as welders would call it spool
Black & Decker's Automatic Feed System is the best for advancing the string.The Poulan Pro Spool is best spool if you have a low tolerance for nuisance in changing and untangling.
The shape is known as an involute the shape is analogous to unwinding a piece of string from a spool representing the base circle diameter of the gear, imagine your pencil at the end of the string and the string kept tight during unwinding, unwind until line meets OD of gear, then apply blend radius at base circle, then mirror about tooth centre line for full tooth profile.