0
What else can I help you with?
I have 3200 watt sub woofers what amplifier should I get with how many watts output?
To power your 3200 watt subwoofers effectively, you should look for an amplifier that can deliver at least 3200 watts RMS (Root Mean Square) power output at the impedance (ohms) of your subwoofers. It's important to match the impedance of your subwoofers with the amplifier to ensure optimal performance. Additionally, consider factors like amplifier efficiency, distortion levels, and compatibility with your audio setup when selecting the amplifier.
What kinda amp should you use for Dual BP1204?
For the Dual BP1204 subwoofers, you should use a monoblock amplifier that can handle at least 600 watts RMS at 1-ohm impedance. This will ensure that the subwoofers receive enough power to deliver their full potential without risking damage to the amplifier or the subwoofers. Make sure to check the manufacturer's specifications for recommended amplifier power ratings as well.
What important factors should I consider when buying an amplifier for my car?
There are a bunch of important factors to consider prior to buying an amplifier for a vehicle. Primarily, you must decide what the amplifier will be primarily used for. If the amplifier will be used for powering subwoofers it would be good to consider the bridged or mono capabilities as well as ohm ratings of the amplifier as well as the draw, or amount of power the amplifier will pull from the car's electrical system. The most important factor in considering an amplifier for powering subwoofers is probably output watts, which will determine the amplifier's power to the speakers and the amount of bass to be transmitted. If the amplifier is to be used to power mid or high range speakers, a multi channel (four or more) amplifier should be considered because of the ability to run multiple sets of speakers or component sets off of the different channels of the amplifier. The considerations inherent to the subwoofer amplifier are also present including watt ouput and power draw, but when selecting a multi cha
Will 300 watt kicker amp push two tens?
It depends on the specific power-handling capabilities of the subwoofers and their impedance. If the subwoofers have a total power handling capacity that is lower than 300 watts and the amplifier can provide enough power at the required impedance, then it should be able to adequately power the two tens. However, if the subwoofers have a higher power handling capacity or the amplifier cannot provide enough power, it may not be sufficient.
What power of amplifier will you need to for 1000 watt subwoofers?
Find out what the rms is for that sub woofer,if it'1000 then find out what the max is,then you could go between the rms power and the max power to get the right amount of watts.
What speakers match a 300 watt 4 channel amplifier?
The ratings for the speakers will depend upon what '300 watts' means. If the amplifier develops 300 watts RMS total across 4 channels, this would indicate 75 watts RMS per channel. Speakers rated at 100 watts should suffice for this amplifier.
What do the subwoofers ohms for?
the ohm is a unit of measurement based off of someones last name. When used in subwoofers, for example 4 ohms or 8 ohms, it actually determines the amount of watts the speaker needs. Like if two identical subwoofers were taken and one was 4 ohms and one 8 ohms and applied say 150 watts to each of them, the 4 ohm would be louder because ohms are the speakers resistance and the lower the ohms the less amount of power it takes for the subwoofer to reach a specific loudness. That's why professional huge subwoofers may be one ohm, because an amplifier that has less power than the sub could still power it because since its one ohm, the 500 watt amplifier at 4 ohms could be 1500 watts at 1 ohm.
Will an amp that puts out 185 watts RMS per channel blow two subwoofers rated at 175 watts RMS if I don't push them?
Wire them in series and you should be ok.
What amp size should you use for 2 12s?
The wire ampacity of #12 copper wire with an insulation factor of 90 degrees C is 20 amps. If the load is of a continuous nature e.g. baseboard heaters then the wire has to be de-rated to 18 amps
How many watts does a alpine 3513 amplifier have?
2x20 Watts
Should your speaker watts be more then your amps?
No, the speaker watts should not be more than the amplifier output in terms of power. It is important to match the speaker's power handling capability with the amplifier's output power to avoid damaging the speakers. It's recommended to have an amplifier that can deliver power within the range recommended for the speaker.
How loud does a monster amplifier get?
A monster amplifier is about 500 watts, which means the amplifier is louder than most.
