0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you make common base transistor or circuit?
it is one of the configuration of BJT ,which is achieved by making the BASE grounded(i.e common base).Here the emmiter serves as the input and collector as the output.
What are common uses of a common emitter amplifier?
bcause amplification factor beta is usually ranges from 20-500 hence this configuration gives appericiable current gain as well as voltage gain at its output on the other hand in the Common Collector configuration has very high input resistance(~750 kilo ohm) & very low output resistance(~25 ohm) so the voltage gain is always less than one & its most important application is for impedance matching for drivingh from low impedance load to high impedance source
What is single tuned voltage amplifier?
it is a circuit consisting of a tuned circuit with a capacitor in parallel with inductor and it is connected to collector terminal in common emitter configuration,, and it is used as frequency receiver
Why more current amplification in common emitter?
A bipolar transistor can be used in different configurations in linear electronic design. Most well known is the common emitter CE configuration with a base current as input signal resulting in a collector signal multiplied by the current gain factor. The second configuration is known as the emitter follower or common collector configuration. Here the input signal is in the form of a voltage between the base and the common connection. The output signal is found in the form of a voltage at the emitter with a relative low output impedance. The voltage swing at the input is almost as large at the output where the input impedance equals the product of the current gain factor and the emitter resistance. The third configuration is known as common base CB. Here the input current at the emitter almost equals the output current at the collector. The current gain is nearly equal to 1.
The dc input resistance of MOSFET is?
it depends on the type of the circuit you are analyzing..it could be a voltage divider, emitter follower, be specific on what type of circuit and maybe i can help you aobut this question.
What is common collector bipolar junction?
A circuit in which the input signal is applied to its base and the collector is earthed (grounded) is known as common collector configuration of BJT (BiPolar Junction Transistor)
How a transistor work as an amplifier and as a switch?
"Transistor" name itself revels it transfers resistance from its input to its output (Transfer of resistance). Input resistance varies when input voltage varies, similarly output resistance varies and this leads to voltage variation at the output. Thus input to output voltage variation is called amplification. this is how transistor can be used as an amplifier. If input voltage is minimum output voltage becomes maximum i.e. its output resistance becomes maximum in common emitter configuration. Thus if no voltage is applied at the input its collector resistance becomes infinite or as if open circuit. Similarly if input current is increased output current increases and out put can behave as short circuit. This is how output current can be switched off or on using no input current or with minute input current. Unlike a digital device, the transistor is an analogue device which can be switch on/off to maximum or any gradient in between. Providing a small AC voltage to the base creates an amplified analogue of this signal across the emitter and collector.
What is the input current for common collector?
from the name itself the common collector has its collector terminal in common with both the input and output circuits of a transistor and the base current is chosen as the input current and the output current is the emitter current
How do you make common base transistor or circuit?
it is one of the configuration of BJT ,which is achieved by making the BASE grounded(i.e common base).Here the emmiter serves as the input and collector as the output.
What does 10 megohm input impedance mean?
10 megohms is the resistance through which 10 volts would push 10 microamps of current. Input impedance is the resistance seen by a signal source when connected to the input Often, this means there is a 10 megohm resistor in series with the input going to a virtual ground on an opamp circuit. 10 megohms is a common input impedance for a digital voltmeter.
How a transistor transfers resistance?
The input current of transistor is approximately equal to output current .Suppose in common base configuration the emmiter current is approximately equal to collector current if neglect the very small value of bae current.Even though the input resistance is not equal to output resistance,the currents are same ,so we can reliase that the transistor transfers resistance to get same currents at both ends.
What are common uses of a common emitter amplifier?
bcause amplification factor beta is usually ranges from 20-500 hence this configuration gives appericiable current gain as well as voltage gain at its output on the other hand in the Common Collector configuration has very high input resistance(~750 kilo ohm) & very low output resistance(~25 ohm) so the voltage gain is always less than one & its most important application is for impedance matching for drivingh from low impedance load to high impedance source
Why don't AC input wires to a transformer just short circuit?
The resistance of the winding in the primary of a transformer constitutes a load. As long as there is resistance then there is no short circuit. A short circuit is considered no resistance which develops an instantaneous high current. That is why fuses and breakers are inserted into the circuit to open the high current flow under a short circuit condition.
What is single tuned voltage amplifier?
it is a circuit consisting of a tuned circuit with a capacitor in parallel with inductor and it is connected to collector terminal in common emitter configuration,, and it is used as frequency receiver
Why you need ground in electronics circuits?
I dont know but it is to get a circuit common and to give a negative input to the circuit
Why is common emitter is greater than common collector?
Common-emitter gives more voltage gain because a common-collector amplifier has a voltage gain of 1. But a common-collector can have a power gain because the input impedance is much more than the output impedance.
What is single tuned amplifiers and what is the hybrid equivalent circuit and how to analyze?
either we have to use a series or parallel RLC circuit to make the circuit tunable either at base or at collector. in series tuned amplifier an input impedance is only due to load resistance and net impedance due to capacitor and inductor is zero, so a huge amount of current flow through the circuit and almost all input all voltage appears across load resistance. so maximum gain is possible in series tuned amplifier. sudhanshu kumar siliguri institute of tech. b-tech, 2nd year, (ECE)
