0
See related links below.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
How insulation resistance of a motor winding checked If the insulation resistance is low What is likely to cause?
gbs bbn b b b sdgb
Can a 415V motor run on 525V?
It is not advisable to do so. You may burn the winding, insulation may fail.
What is the length of time that a motor can safely run on starting and full load current?
It depends on the insulation provided in winding, motor can safely run on full load current. and over that it may burn but depends on cooling system of the motor. Motor can burn if insulation fails, failure of insulation depends on only the temperature rise.
What happens if field winding of a running dc shunt motor suddenly breaks open?
when the field winding of a running dc shunt motor suddenly breaks open the motor fails to run because in the motor the stationary winding is armature and rotatory is field winding
Why is class A winding insulation is only used in oil filled transformers?
This is because the oil has flash over point at 140 deg.Cl and the winding insulation cannot exceed the flash point of the oil.
How insulation resistance of a motor winding checked If the insulation resistance is low What is likely to cause?
gbs bbn b b b sdgb
Can a 415V motor run on 525V?
It is not advisable to do so. You may burn the winding, insulation may fail.
What is the length of time that a motor can safely run on starting and full load current?
It depends on the insulation provided in winding, motor can safely run on full load current. and over that it may burn but depends on cooling system of the motor. Motor can burn if insulation fails, failure of insulation depends on only the temperature rise.
Why you do insulation resistance test?
in order to avoid unwanted short circuit break downs.... short circuit can burn the transformer and motor winding.... Megger is the device used to check the insulation .
How do you increase the insulation resistance of a motor?
You can increase the insulation resistance of a motor by keeping it dry. moisture makes the IR drop. If possible to dismantle, try to re-varnish the winding and dry it inside a furnace or oven for at least 24 hours.
Why insulation is not required in winding wire side by side in motors?
Actually it is insulated, the red coating of varnish is the insulation. Also after a motor is wound, it is soaked in varnish and baked giving it added protection.
What is the reason for the insulation failure of a single winding of a motor and all 3 phase windings of an immersible pump?
The insulation on wires of a motor are very thin and in close proximity in the winding. If too much current flows the wire can heat up and insulation can melt. This deterioration can happen over time. The bare wire can then come in contact with metal parts on the motor and cause a direct short or can short with other parts of the winding and cause a short that effectively reduces the length of the winding. This can happen in both cases you asked about. On an immersible pump if you are demanding a heavier duty cycle on the pump it can fail prematurely. This can happen if your pressure tank on a well is not of sufficient size to handle your water demands.
How is the resistance of a motor winding expressed?
The resistance of a motor winding is expressed in
What is the myelin sheath similar to?
myalin sheath is very similar to the insulation in your motor winding. Only difference is that man is using this insulation from century or two and nature has been using the same since about three billion years.
The function of a start winding in a split-phase motor is to?
a start winding on a motor is used to add torque to start a motor, and more importantly to establish the direction that the motor will turn. to reverse a motor normally means to reverse the start winding. the run winding will work the same in either direction, the start winding determines the direction.
What happens if field winding of a running dc shunt motor suddenly breaks open?
when the field winding of a running dc shunt motor suddenly breaks open the motor fails to run because in the motor the stationary winding is armature and rotatory is field winding
One induction motor winding is burned and still showing equal winding resistance and low insulation resistance value?
you probably have a winding to winding short. you need an a pluse tester or an ac ohmmeter each coil is slipped into a slot lined with fish paper (cambric) each wire in the coil is insulated with a thin layer of varnish with formed coils rather them mush coils it can be a one turn short mush coils give several turns it acts like a transformer with a short in the secondary
