answersLogoWhite

0


Best Answer
Copy

After you remove the plastic shroud and metal box directly below it you can gain access to the front three. As for the back, remove the connector and screw at the 7 o'clock position on the dist cap off to the side. You CAN reach the back three with two 6 inch socket extenders and without remvoing any other engine parts. Should take 30 min regardless of experience. I just did mine and I'm not a mechanic.

User Avatar

Wiki User

โˆ™ 2007-06-28 00:31:02
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: Is it difficult to replace the spark plugs on a 99 Cougar and are special tools required or do any engine components need to be removed?
Write your answer...
Submit

Related Questions

How do you replace fuel injectors in a1993 mercury villager?

The upper intake manifold must be removed for access, as well as other components. Once that is done, the fuel rail can be unbolted and the injectors removed.


How difficult is it to replace a fuel pump for a 98 Nissan Altima?

It is a difficult repair because the fuel tank must be removed unless there is an access panel above the fuel tank.


How hard is it to replace the lifters on a 1995 Chrysler 3.8 liter v-6?

It is difficult, the cylinder heads need removed.


Can the pickup bed be removed to replace the fuel pump on a 1995 ford ranger?

It may be more difficult to remove the bed than to drop the tank.


How do you replace the rear wheel bearings on a 2003 Escape?

take to trained technician rear suspension needs to be removed and a press and specialty tools are required!


When the county removes large old oaks for construction aren't they required to replace trees that were removed Who do I contact to talk about this issue?

Your local building and zoning department.


Where is the heater core located on a 1993 Toyota Camry and how difficult is it to replace it?

Passenger side, near the firewall. It is not difficult to replace, it is just very difficult to get to.


How do you replace the wheel bearing on the front of the Dodge stratus 1999?

The front spindle must be removed as the bearing is pressed in. Not a job for a beginner, but if you have some auto expertise, not too difficult...


How much does it cost to put a timing belt on a 1986 Toyota MR2?

The timing belt is not difficult to replace nor is it expensive in and of itself. The problem is that the timing belt is difficult to get to. Mechanics also suggest that you replace the water pump and possibly some other components so that the the same area does not have to be dismantled in the future to do these repairs. It is not hard to get into the $400+ range.


Is it difficult to replace BMW battery?

no


How do you replace the oil pump on an 1997 Chevrolet Malibu. What tools are needed?

The oil pan must be removed. No special tools required, just normal mechanics tools.


Is a landlord required to replace carpet before a new tenant moves in?

No--unless the carpet is in disrepair (substantial rips/tears), has odors that cannot be removed by cleaning (by the landlord), etc.


How do you remove the dash in a 1989 g20 or even how do you replace the speakers in the dash?

You can go to Crutchfield and they will send you the intricate details for this job. It is a pain. The heater has to be removed and the dash, it is difficult and time consuming.


How to replace a 1998 zx2 headlight?

the bumper will have to be removed.


How do you lower the rear of a Peugeot 206?

as the rear is torsion it is not straight forward. the torsion bars have to be removed one side at a time, with the torsion bar out simply adjust hub the required amount and replace torsion bar. then do the other side. this can be hard as the bars can be difficult to remove. best left to professional should cost between £60-£100


How do you replace the battery in a 1984 Corvette?

The fiberglass panel at the side of the battery has to be removed and the battery is removed sideways.


You have several park benches in your park and want to replace the slats with recycled material slats you have been unable to find any?

Several of the commercial grade recycled products can be milled and worked like wood and shaped into the dimensions required, HOWEVER, most wooden components in benches are also structural components and plastic composites may not have the strength or rigidity to directly replace the wood components. The material manufacturers have technical support people that may be able to help you decide.


Why artificial pacemaker replacement is required?

Replacement is required in order to replace the battery.


How do you replace a heater core in a 1974 Monte Carlo 400 CI?

This is sort of a difficult job. The black housing under the hood (on the passanger side) has to be removed. The heater core is mounted inside that housing.


How do you change tail light bulb on 2003 Mazda protege 5?

Basically, there are three bolts that you need to take out. Then you pull off the tailight assembly. Replace the bulb as required and then replace the taillight on the car ncmuding any bolts you removed. Refer to your owner's manual.


How do you replace radiator Ford Fiesta 2006?

The replacing of a radiator in a 2006 Ford Fiesta should be done by a professional. There are multiple components around the radiator that, if accidentally removed or damaged, can cause further, more damaging damages to the vehicle.


How do you replace dash lights 1994 mercury villager van?

To replace lamps the cluster must be removed.


Is it required by law to replace deployed airbag?

no


How do you replace the battery in a 1984 Corvette C4?

The fiberglass panel at the side of the battery has to be removed and the battery is removed sideways.


How do you replace a flexplate on a 1994 Jeep Cherokee?

The transmission will have to be removed.