0
Oil Pump Inspect | Service | Replace NOTE
The instructions here for the installation of either type of pump are general. Specific installation directions, as well as oil priming instructions (if necessary), can be found in the service manual. In the case of a typical distributor-driven oil pump, the installation should be performed in the following manner:
Installation of an oil pump driven by the distributor. Courtesy of General Motors Corporation-Chevrolet Motor Division.
* Position the intermediate drive shaft into the distributor socket. * With the shaft firmly seated, the stop on the shaft should touch the roof of the crankcase. * Remove the shaft and position the stop as necessary. * With the stop properly positioned, insert the intermediate drive shaft into the oil pump. Install the pump and shaft as an assembly. * Do not attempt to force the pump into position if it will not seat readily. The drive shaft hex might be misaligned with the distributor shaft. * To align, rotate the intermediate drive shaft into a new position. * Tighten the oil pump attaching screws to torque specifications. * Clean and install the oil pump inlet tube and screen assembly. The installation of a typical camshaft-driven oil pump is done as follows:
Installation of an integral oil pump driven directly by the crankshaft. Courtesy of American Honda Motor Co., Inc.
* Apply a suitable sealant to the pump and block. * Install the pump to its full depth and rotate it back and forth slightly to ensure proper positioning and alignment through the full surface of the pump and the block machined interface surfaces. * Once installed, tighten the bolts or screws. The pump must be held in a fully seated position while installing bolts or screws.
Look for More Parts A B C D E F G H I
J K L M N O P Q R
S T U V W X Y Z Related Parts: Oil Pan Gasket Oil Pump Drive Gear Oil Pump Shaft Oil Pump Screen Return to top.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you change oil pump on 1999 plymouthy neon?
Answering "How do you change oil pump on 1999 plymouthy neon?"
How do you change oil pump 1999 dodge?
Remove the oil pan, remove the pump, and replace it.Remove the oil pan, remove the pump, and replace it.
How hard is the oil pump to replace?
What make and model car, which engine. Your question is to vague to give a direct answer.
How do you replace the oil pump on a 1999 Oldsmobile alero with a 3.4 liter V6?
how do you replace the oil pump
How do you replace oil pump on 1994 jeep?
You must remove the oil pan to access the oil pump. It is simple to replace once you get to it.
How do you replace the oil pump on a Mazda Protege?
Could you tell me how would you replace the oil pump on a Mazda Protege?
How do you replace the Toyota Camry 1998 oil pump?
You need to follow the same procedure as for timing belt replacement. But in the case of the oil pump you have to remove the oil pan too. There is a strainer attached to the oil pump from the bottom you will have remove it too. Then replace the oil pump, make sure that you have replace the oil pan gasket, and oil pump gasket.
On a 2000 dodge neon where is the oil pump located?
the oil pump sits on the nose of the crankshaft, behind the timing belt sprocket.
How do you replace the oil pump on a 1991 Cadillac Deville?
You have to remove the oil pan to get at the oil pump.
How do you replace a Hyundai elantra oil pump?
My Hyundi elantra has the oil light on but it has oil in it. Is the oil pump broken
Picture how oil replace oil pump?
The picture of how to replace an oil pump varies between models and brands. A service manual for your specific car will have pictures with instructions of how to chance the pump.
How do you change the oil pump on a 2001 Plymouth Neon?
You will need to use the Haynes repair manual, Dodge Neon 2000 thru 2003. Book #30036 I used it to change an oil pump and it helped alot!
