0
Is the compressor motor and condenser fan motor wired in series or parallel?
Wiki User
∙ 12y ago
series
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is a computer motor?
Its a motor which is turned on or off by the actuator.
What is made from renewable resources a plastic bag a computer keyboard a wooden spoon or a motor oil?
Motor
How do you build an electric motor with over 2000 RPM?
an electric motor can be build with over 2000 rpm,by increasing the supply frequency.
Is a motor an input or output?
The monitor is an output device......
How much energy does a 75kW motor use?
Multiply 75 kW by T hours of use = 75T kWh, which is how much energy the motor uses.
If the condenser motor runs but the compressor will not run what would check in most cases?
check to see if your lowon freon
What different types of DC motor are there?
Series wound. Parallel wound. Series/parallel or Compound wound.
If the condenser fan motor goes out and the unit continues what will happen?
overheating of the c.motor and will turn to stop or burn the winding of the compressor motor due to over heating
Which motor is used in automobiles for starting purpose?
A DC series-parallel compound motor.
Why does your heat pump keep blowing breakers?
There is a short somewhere. Probably the condenser fan motor or the compressor. Time to have it checked out by a competent, trusted techenician.
What is DC shunt motor?
A shunt DC motor connects the armature and field windings in parallel or shunt with a common D.C. power source. This type of motor has good speed regulation even as the load varies, but does not have the starting torque of a series DC motor
How do you reset a goodman compressor?
Any compressor has an internal overload which may go off due to bad condenser fan motor, clogged condenser, restriction of air, the only way to test is to check the condinuity between terminal common start and run if common open shut off system and allow 24 hours to reset if it doesn't reset may need new compressor
What is shunt and series motor?
A series motor is one in which the field windings are in series with the armature windings. So the torque is proportional to the square of the supply current.'Shunt' is an archaic term for 'parallel'. So a shunt motor is one in which the field winding is in parallel with the armature windings. So the torque is proportional to the supply current.
What is wrong when you home AC blows hot air?
Most commonly, the compressor is not working, the evaporator is blocked by dirt, the condenser motor isn't woring. A trained technician needs to evaluate
What is difference between synchronous motor and synchronous condenser?
a synchronous condenser is over excited synchronous motor under no load
Are the interpoles in a DC motor connected in series or in parallel with the armature?
Hi, Always interpoles are connected in series with armature. N.V.B.V. Prasada Rao
What is an hermetic compressor?
a fully welded or serviceableIn hermetically sealed compressor, the compressor and the motor are enclosed in the welded steel casing and the two are connected by a common shaft. This makes the whole compressor and the motor a single compact and portable unit that can be handled easily. The hermetically sealed compressor is very different from the traditional open type of compressors in which the compressor and the motor are different entities and the compressor is connected to the motor by coupling or belt.Construction of the Hermetically Sealed Reciprocating CompressorIn hermetically sealed compressor, in one side of the enclosed casing the various parts of the compressor like cylinder, piston, connecting rod and the crankshaft are located. If it is a multi-cylinder compressor, there are more than two cylinders inside the casing. On the other side of the casing is the electric winding inside which the shaft of the motor rotates. This motor can be single speed or multi-speed motor. In hermetically sealed compressors the crankshaft of the reciprocating compressor and the rotating shaft of the motor are common. The rotating shaft of the motor extends beyond the motor and forms the crankshaft of the hermetically sealed reciprocating compressor.All these parts of the hermetically sealed compressor are assembled and enclosed in a strong and rigid casing made up of welded steel shell. The steel shell comprises of two half rounded steel bodies that are welded together to form the casing for the hermetically sealed compressor. In some cases the two halves of the shell can be bolted together instead of welding, which permits easy opening of the casing in case of compressor burnout.The hermetically sealed compressors have inbuilt lubrication system for the lubrication of the piston and cylinder and crankshaft. The lubricant also acts the coolant for the piston and cylinder. Additionally, the cool suction refrigerant also offers cooling effect. Externally, the casing has refrigerant suction and discharge connections that are connected to the evaporator and condenser respectively. There is also socket for the electrical connection.The typical condenser unit with the hermetically sealed compressor is shown in above fig. Such condenser units are called as hermetic condenser units. In the other image various parts of hermetically sealed multi-cylinder reciprocating compressor are shown.Types of Hermetic CompressorsOne of the most popular types of the hermetically sealed compressors are the reciprocating compressors. They were the first to be used as the hermetically sealed compressors are still being used widely. These days the vane type of rotary compressor has become more popular. It is considered that the rotary type of hermetically sealed compressor consumes less electricity, makes lesser noise, requires lesser maintenance, and is cheaper than the reciprocating type of hermetically sealed compressor. This is because the rotary compressors has less frictional parts and have only a rotor. The centrifugal types of hermetically sealed compressor are used for the large units.
