0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Which type digital voltmeter is the of fatest all digital voltmeter?
You mean fastest? Digital voltmeter gives reading in seconds.
What is voltmeter?
A voltmeter is a measuring instrument that is used in the measurement of the electric potential in volts.
Why there is an extension range of voltmeter when a series resistance not equal to voltmeter is used?
why is extention
Which voltmeter will used for measuring 50kv dc?
Any standard voltmeter but however the voltage to be measured must be stepped down to a safe value using a Potential transformer.
What is instrument specially designed to measure voltage?
The Ammeter XD
What is the use of the oscilloscope?
If you use a voltmeter to observe a voltage, it can only respond slowly, so if you want to observe a voltage that changes in fractions of a microsecond, you need a voltmeter that can respond at such speeds. It is called an oscilloscope.
How a Cathode Ray Oscilloscope is used to measure Alternating current?
An oscilloscope is, essentially, a voltmeter -it measures current by measuring the voltage drop caused by that current across a standard resistance.
What is the purpose of the voltage divider control in oscilloscope?
This control reduces the amplitude of the applied signal to a point where the whole signal can be displayed on the oscilloscope screen. The amount of voltage reduction is marked on this control switch so that it can be used as a voltmeter.
How do you measure amplitude of a ripple?
Most true RMS voltmeters can measure the value of a ripple voltage on top of a DC supply, when you place it in AC mode. You can also place a small capacitor in series with a DC voltmeter and that would measure the ripple. The real way to do this, because ripple voltage is not sinusoidal, is to use an oscilloscope, particularly if you want the peak values.
What are the advantages of using an Oscilloscope over a voltmeter?
In the name of Allah,the most Gracious,the most Merciful... The Oscilloscope has several advantages over a voltmeter, for example if you want to determine a signal parameters [ voltage values (max,peak-to-peak,rms,average...etc),frequency,offset...etc ] using measurement tools: 1- You can use the Oscilloscope whatever the signal frequency is, but you can't use the Avometer unless the signal frequency is 50 to 60 Hz. 2- The Oscilloscope shows you the shape (form) of the signal, while the Avometer doesn't. 3- You can determine the maximum value of the signal (max voltage) and peak-to-peak voltage when you observe the signal on an Oscilloscope,hence you can calculate the rms (root mean square) value, i.e. the effective value , the average value and the offset of signal form the time axis (the horizontal axis). While an Avometer can only give you the rms value.
What precautionary steps have to be taken when using an oscilloscope?
Beware using ground clips for high speed measurements.Beware of oscilloscope bandwidth limitations.Ensure the correct triggering.Use the right oscilloscope probe.Remember to calibrate the oscilloscope probe.Beware using ground clips for high speed measurements.Beware of oscilloscope bandwidth limitations.Ensure the correct triggering.Use the right oscilloscope probe.Remember to calibrate the oscilloscope probe.
Who invented the oscilloscope?
Karl Ferdinand Braun invented the Oscilloscope in 1897
What is CRO and AFO?
Audio Frequency Oscilloscope and Cathode Ray Oscilloscope
What are oscilloscope probes use for?
Oscilloscope probes are used as part of an Oscilloscope. These are the pieces that connect to your circuit in which you would like to measure its sine waves.
How do you test a voltage rectifier?
If you actually mean rectifier (rather than regulator), then you can determine if it is performing its base function of converting alternating current to direct current by using a voltmeter. If the rectifier is functioning, you should read a percentage (which depends upon whether it is a half-wave or full-wave rectifier) of the AC peak input value on the DC range of a voltmeter. Using an oscilloscope, you can clearly view the half-wave or full-wave unidirectional (positive or negative only) pulses produced at the output of the rectifier. If the rectifier is blown and is conducting in both directions you will see nothing on a DC voltmeter range (the average value of an AC waveform is zero), and on an oscilloscope you will see the full peak-to-peak AC input waveform at its output.
What is the resistance of an ideal oscilloscope probe?
The resistance of an ideal oscilloscope probe is infinity.
Why current cannot be measured directly using an oscilloscope?
A standard oscilloscope is designed to measure voltage, you need a current probe for your oscilloscope to measure current.
