answersLogoWhite

0


Best Answer

Removal

1. Disconnect negative battery cable, then positive battery cable. Remove intake manifold cover. Loosen

fuel filler cap to relieve tank vapor pressure. Connect fuel pressure gauge (J-34730-1) to fuel pressure

connection. Place fuel pressure gauge bleed hose in a container and open gauge bleed valve to relieve fuel

system pressure.

replaced in original location to ensure proper pinion to flywheel clearance.

2. Disconnect Intake Air Temperature (IAT) sensor electrical connector. Disconnect crankcase vent pipe at

air intake duct. Remove air intake duct and air cleaner housing. Disconnect transaxle vent hose and

vacuum lines at Idle Speed Control (ISC) actuator bracket. Disconnect vacuum manifold at throttle body.

Disconnect Throttle Position (TP) sensor and ISC actuator electrical connectors. Disconnect cruise

control servo vacuum hoses and electrical connector. Disconnect cruise control cable at throttle body.

Remove cruise control servo and bracket.

3. Disconnect accelerator cable at throttle body and ISC actuator bracket. Disconnect front bank spark plug

wires and position aside. Disconnect throttle body coolant hoses at throttle body and surge tank pipe.

Disconnect Exhaust Gas Recirculation (EGR) pipe at throttle body spacer. Disconnect brake booster

vacuum hose at intake manifold vacuum fitting. Disconnect fuel rail ground wire at rear cylinder head.

4. Disconnect quick-connect fittings at fuel rail. Remove fuel rail bracket at EGR valve. Disconnect Positive

Crankcase Ventilation (PCV) hose at intake manifold. Disconnect injector harness main connector.

Remove 6 bolts and 4 studs securing intake manifold, and remove intake manifold.

5. Remove starter solenoid terminal "S" nut and battery cable nut. Separate wiring from starter. Remove

starter mounting bolts and any shims. Remove starter.

Installation

1. Before installing starter onto engine, tighten inner solenoid terminal nuts to ensure they are secure in cap.

Starter failure may occur due to terminal or cap damage. Install starter and wiring. Tighten starter

mounting bolts to specification. Refer to the TORQUE SPECIFICATIONS table.

2. Install intake manifold with throttle body attached. Tighten 6 intake manifold bolts and 4 intake manifold

studs to 89 INCH lbs. (10 N.m). To complete installation, reverse removal procedure.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Is there a diagram showing how to take the starter off a 1995 Oldsmobile aurora?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you change the starter on a 96 Oldsmobile aurora?

Remove the intake manifold. The starter is underneath.


Where is the starter in a 2001 v8 aurora Oldsmobile?

It's under the intake manifold. Remove that & the starter is accessible.


Where is the starter in a 1998 Oldsmobile aurora?

under the intake manifold you have to remove the engine cover to get to it.


Oldsmobile aurora engine diagram?

Go to library and get a Chilton repair manual you can find most of your information for engine diagram.


Where is a starter located on an 96 Oldsmobile aurora?

The starter on this car is located under the intake manifold, in the engine valley. Tech JK -------------


When was Oldsmobile Aurora created?

Oldsmobile Aurora was created in 1995.


Where is the starter located on a 1999 Oldsmobile aurora?

over the traney in back ov morter not ezy to cange good luk


Where is thethermastat on a 2001 Oldsmobile Aurora?

wheres the thermostat on a 2001 Oldsmobile aurora


Where is the crank shaft sensor on a 2001 olds aurora 4.0 L Eng?

Go to www.autorepair.about.com and search on "crank sensor aurora 3.5 2001". One of the hits will be a diagram showing the sensor above the starter. There is also a link to the replacement procedure and tells how to do a "relearn" after replacing the sensor. r


How do you replace the fuel injectors on a 1997 Oldsmobile aurora?

where are the fuel injectors in a 1997 oldsmobile aurora


Where is the knock sensor located on a 1996 Oldsmobile aurora?

Where is the Knock Sensor located on a 1996 Oldsmobile Aurora?


2001 Oldsmobile aurora ac compressor bypass?

can you bypass a 2001 oldsmobile aurora ac compressor?