answersLogoWhite

0


Best Answer
Copy

It's on the intake manifold, just to the right of the throttle body. Two bolts hold it in place. When you lift the EGR valve, make sure you have a new gasket to replace the old one. At that point, it's just a matter of cleaning the built up deposits. Use a shop-vac to keep the deposits from entering back into the intake.

2009-05-29 04:50:05
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...
Still have questions?
imp

Related Questions

How do you clean the egr valve runner and ports on a 4 cylinder Honda Accord?

You can clean the E GR valve by removing the valve and soaking it in a cleaning solvent. You can clean the ports with the same solvent. Wipe everything dry after cleaning.


How do I clean an EGR valve?

They usally don't need cleaning most require replacement or the eve ports need cleaning


Where is the heater valve in a 1994 Chevy Suburban?

where is the heater control valve on a 1994 2500 suburban


Need location of expansion valve on a 1997 Chevrolet Suburban?

Where is front expansion valve for chevy suburban 1997


If 1993 suburban rear ac not cold how can check the expansion valve?

If 1993 suburban rear ac not cold how can check the expansion valve?


Where is the PCV valve on a 2002 Chevy Suburban 6.0 liter engine?

The PCV valve on a 2002 Chevy Suburban 6.0 liter engine is located in the engine. You cannot miss the valve.


How do you clean the shower-tub mixer valve?

From a plumbing or cleaning point of view? Whichever, a cloth, bucket and soap will do the trick.


Where is the pvc valve located on a 2001 suburban 5.3L?

where is the pcv valve located on a 2001 chevy suburban It is stuck in a rubber hose and pushed into the top rear drivers side valve cover.


How do you tell difference between exhaust valve and intake valve on 1998 suburban 5.7?

The intake valve is bigger.


Does a 1993 4x4 Suburban with overdrive have a modulator valve?

NO IT DOES NOT.


What does a egr valve on 1999 gmc suburban look like?

Depends on the year. Here is a site that has pictures of an EGR valve for a 1997 - 1999 Suburban: http://www.racepages.com/products/?D=gmc+suburban+egr+valve&Nty=1&Ntx=mode+matchallpartial&Ntk=Main&N=4294950670+4294963366+9926&Dx=mode+matchallpartial&Ntt=gmc+suburban+egr+valve Go to www.racepages.com and search for an EGR valve for your year rig.


Where is the PCV valve on an 07 suburban?

They are normally found on the left or right side valve cover


How do you clean the iac valve on a 1998 mustang gt?

You can try cleaning it with carb cleaner by removing it and spraying carb cleaner into the port with the valve stem showing. That said, you may be better off replacing it as it is hard to properly clean it. There are some simply instructions for replacing it at Autoclinix.com.


Where is the PCV valve on a 2003 Chevy Suburban?

Its in the drivers side valve cover in back near the firewall


How do you clean the IAC valve on a 1999 Honda CR-V?

The Haynes Manual (copyrighted) gives no instructions for the cleaning of the IAC, only its replacement if defective.


What is the cost for a valve job on a 1999 GMC suburban?

A valve job for your 1999 GMC Suburban will cost approximately $800. The parts will cost around $200 and require 10 hours of labor.


On a 1996 Chevy Suburban the brake system incorporates a dump valve What does this dump valve do and or where is it?

The brake dump valve on a 1996 Chevy Suburban is used for bleeding the brakes after new brake pads are installed. It is located on the master cylinder for each brake.


I have cleaned my idle control sensor but still idles rough How can I clean the idle passage also The maf looks good and my tps was replaced and throttle bore cleaned?

try cleaning the egr valve passage and egr valve.


Why does my car stall while idling?

try cleaning the throttlebody and Air Control Valve and clean the bore of the A.C.V. with a mas air flow cleaner you can by at autopart store


How do you clean egr valve on vauxhall zafira 1600?

how do you clean a egr valve on a vauxhall zafira 1.6


How do you remove the valve cover on a 1998 suburban?

To remove a valve cover on a 1998 Suburban, you need to take all of the valve cover bolts out. Lift the cover slightly, then see what is in the way of sliding it out (hoses, fuel rail, etc..) Remove and items blocking the removal then lift the cover off. Make sure to clean the cover and head of all old gasket material before installing a new gasket and bolting the cover back on.


Where is the PCV valve in a 2000 Chevy Suburban?

if equipped it is on the driver side valve cover in the rear pointing straight up


What could be the cause of a rough idle while in park on a 1994 Lincoln town car?

Remove the EGR valve and clean the passages and/or clean the MAF sensor in the air intake tube (use alcohol and be VERY carefull when cleaning the two small wires). Could also be the IAC or idle air control valve. There are very nice writeups on cleaning the IAC, MAF and EGR passages in the tech section at www.lincolnsonline.com


How you clean egr corsa c?

Remove the EGR valve from the Corsa. Wash the EGR valve with carburetor cleaner. Make sure that the valve is clean of gunk and let it dry. Reinstall the valve.


Where is the oil drain plug for the 2000 suburban Chevy?

on the bottom of the cylinoid valve