Ford Aerostar
Ford Windstar LX
Ford Expedition XLT

On a 1991 Ford Aerostar with dual heat why would the front get warm but the back does not?

575859

Top Answer
User Avatar
Wiki User
2005-09-23 23:55:15
2005-09-23 23:55:15

The rear heat coil is operated by a solenoid valve located in the rear side compartment. You have to remove the middle seat and access the compartment by removing the cover where the blower is located. The valve is controlled electrically by the front or rear controls. There are two possible problems: there is no power going to the valve, or the valve itself is bad. Check the voltage going to the valve first with a meter. If you have power going to the valve then the valve needs to be replaced.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

On a Ford Aerostar 3.0 ( and 4.0 ) 3 - 6 2 - 5 1 - 4 front of Ford Aerostar

User Avatar

how do you fix a gas guage on a 1989 ford aerostar

User Avatar

There are ( shock absorbers ) on a 1997 Ford Aerostar ( front and rear )

User Avatar

For a 1994 Ford Aerostar , 3.0 ( and 4.0 ) 3 - 6 2 - 5 1 - 4 front of Ford Aerostar

User Avatar

On a 1993 Ford Aerostar 3.0 ( and 4.0 ) 3 - 6 2 - 5 1 - 4 front of Ford Aerostar

User Avatar

My 1995 Ford Explorer has a diagram in the front of the engine compartment showing how the serpentine belt is routed . Does your Ford Aerostar not have that .

User Avatar

On a 1997 Ford Aerostar 4.0 ( and 3.0 ) The engine cylinder locations are numbered : 3 - 6 2 - 5 1 - 4 front of Ford Aerostar

User Avatar

On a 1994 Ford Aerostar , 3.0 L ( and 4.0 L ) 3 - 6 2 - 5 1 - 4 front of Ford Aerostar

User Avatar

My friend said his ford Aerostar was front wheel drive? ------------------------------------------------------------------------------------ As far as I know the Ford Aerostar has always been rear wheel drive or all wheel drive capable

User Avatar

On a 1991 Ford Aerostar 3.0L : The firing order is ( 1 - 4 - 2 - 5 - 3 - 6 ) The distributor rotor turns CLOCKWISE ( looking from the top ) The engine cylinder locations are numbered : 3 - 6 2 - 5 1 - 4 front of vehicle

User Avatar

On a 1994 Ford Aerostar , 3.0 liter V6 and 4.0 liter V6 : 3 - 6 2 - 5 1 - 4 front of Ford Aerostar

User Avatar

The Ford Aerostar front hub bolt should be torqued at 120 pounds of pressure. The hub bolt should not be over tightened as it can ruin the wheel seal.

User Avatar

No, they are two completely different designs. aerostar is rear wheel drive ,taurus front wheel drive.

User Avatar

The price varies for a head gasket by location for a 1991 Ford Aerostar van. The approximate price for the head gasket if you are going to do all repairs yourself is approximately $80.00.

User Avatar

Ford Aerostar was created in 1986.

User Avatar

On a 1994 Ford Aerostar ( 3.0 and 4.0 ) 3 - 6 2 - 5 1 - 4 front of vehicle

User Avatar

Should be on the bottom of th hood after you prop it up look at the front edge of the hood. If not check the manual. Or google images.

User Avatar

A 1993 Ford Aerostar would have come from the factory with ( 5W-30 )

User Avatar

Yes, both the 3.0 and the 4.0 are fuel injected.

User Avatar

On a 1995 Ford Aerostar 4.0 and 3.0 V6 engines : 3 - 6 2 - 5 1 - 4 front of vehicle

User Avatar

How do you remove the rotors on a 1992 ford aerostar?"

User Avatar

On a 1997 Ford Aerostar : The fuel pump shut off switch ( inertia switch ) is in the front passenger footwell , behind the kick panel * the kick panel is the interior trim panel , just in front of the front door , by the persons feet

User Avatar

as far as i know it on the vac by the firewall left side


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.