0
Putting intake gasket in 1997 olds cutlass 3.1 engine got the push rods mixed up could you help me where the short ones go and the long ones?
Wiki User
∙ 12y ago
1997olds3.1 engine when hot water backs up throught the resivour and motor makes knocking sound
good luck because push rods have wear patterns on them at the end that goes on first and there order specific
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you change the lower intake gasket on a 95 Olds Cutlass Supreme 3.4DOHC?
Remove the 1995 Oldsmobile Cutlass intake manifold retaining bolts. The manifold will come off. Remove the old gasket. Clean the surface. Put the new intake gasket and tighten the intake manifold retaining bolts.
What is a intake gasket?
The intake gasket is the gasket that conncects from your air filter into your intake manifold
How do you change the intake manifold gasket on a 1998 park avenue?
What engine? and ensure it is a bad gasket, not an intake plentum.
How do you change intake manifold gasket on 2001 stype Jaguar?
jaguar 2001 Lower Engine Intake Manifold Gasket
If not the head gasket how is water getting into the oil?
Intake gasket leaking on the inside of engine.
Where is the transmission dipstick located on a 1999 Oldsmobile Cutlass?
Between the engine and firewall labeled TRANS. Under the Air Filter/ Intake box there is a red cap on the transmission for putting in fluid. There is no dipstick that I know of on a 1999 Cutlass w/ 3100 "J" motor.
What will a bad intake gasket do?
It can allow water to mix with the engine oil and destroy the engine.
What is wrong when a 1995 cutlass and recently it started to have high temp and water in the oil heater not getting warm what could be wrong and is it too much to fix?
Blown intake manifold gasket or blown head gasket, figure on $600 to $650 to get intake gasket fixed and if a head gasket your looking at least $1,000.
What is the definition of an intake gasket?
It is the sealing part that seals the intake manifold to the cylinder heads and to the top of the engine block. The intake manifold is the part that distributes the air to the cylinders. It also can house the thermostat, the injectors, the throttle plate. An intake gasket could leak coolant, engine oil, or engine vaccuum.
Where could engine coolant be leaking from on rear topside of engine on a 1998 350vortec it pours coolant out but can't see where from?
It is common for the intake manifold gasket to leak antifreeze from the corners of the intake. Need to replace intake gasket. Be sure to look closely at the intake were the gasket seals against it for pitts in the intake. There is a heater hose that goes into the intake on right rear corner in the back, but uo on top of intake. check closely. It is common for the intake manifold gasket to leak antifreeze from the corners of the intake. Need to replace intake gasket. Be sure to look closely at the intake were the gasket seals against it for pitts in the intake. There is a heater hose that goes into the intake on right rear corner in the back, but uo on top of intake. check closely. It is common for the intake manifold gasket to leak antifreeze from the corners of the intake. Need to replace intake gasket. Be sure to look closely at the intake were the gasket seals against it for pitts in the intake. There is a heater hose that goes into the intake on right rear corner in the back, but uo on top of intake. check closely. It is common for the intake manifold gasket to leak antifreeze from the corners of the intake. Need to replace intake gasket. Be sure to look closely at the intake were the gasket seals against it for pitts in the intake. There is a heater hose that goes into the intake on right rear corner in the back, but uo on top of intake. check closely. It is common for the intake manifold gasket to leak antifreeze from the corners of the intake. Need to replace intake gasket. Be sure to look closely at the intake were the gasket seals against it for pitts in the intake. There is a heater hose that goes into the intake on right rear corner in the back, but uo on top of intake. check closely.
Where is the upper manifold gasket located on a 2000 Chevy s10?
Assuming this is a 4.3L engine, the upper intake manifold gasket would be between the upper intake manifold and the lower intake manifold.
How do you identify intake gasket problem?
Simple method... get some carb cleaner or starting fluid. With the engine running, spray the area where the intake manifold gasket is. If you experience sudden bursts of increased RPMs, you have an intake manifold gasket issue.
