If the oil light is shining check the engine oil this could be a sign of low oil pressure. This is serious because it means there may be little to no oil in the engine. No oil will caused the engine to destroy itself. If the fluid is low pour more oil in. If not take the car to have a diagnostics done.
It is designed to last the life of the engine and is normally replace when the engine is overhauled.
Turn the key on then push the gas pedal to the floor 3 times. Then turn key off and then start engine.
Acura CSX2006-2010Turn the ignition to (II) - do not start the engine.Press the SEL/RESET button on the steering wheel until you see the engine oil life display.Press and hold the SEL/RESET button on the steering wheel for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multi information display.Select RESET by pressing the INFO (â–²/â–¼) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.Turn the ignition off and then start the engine to verify the indicator has been reset.
Turn ignition to run engine off. Display OIL LIFE RESET in the Driver Information Center (DIC). Press and hold the ENTER button for at least one second. An ACKNOWLEDGED' display message will appear for three second or until the next button is pressed. This will tell you the system has been reset. Turn the key to OFF. If the "CHANGE ENGINE OIL" message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
Turn the ignition switch to the ON (II) position Press the Select/Reset knob repeatedly until the engine oil life is displayed. Press the Select/Reset knob for about 10 seconds, The engine oil life and the maintenance item code(s) will blink. Press the Select/Reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to "100".
1.Turn the ignition switch to the ON (II) position. 2.If the engine oil life is not displayed, press the SEL/RESET button on the steering wheel repeatedly until the multi-information reads oil life. 3.Press and hold the SEL/RESET button on the steering wheel for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multi-information display. 4.Select ''RESET'' by pressing the INFO ( / ) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to ''100.'' If you want to cancel the oil life reset mode, select ''CANCEL.''
1.Turn the ignition switch to the ON (II) position. 2.If the engine oil life is not displayed, press the SEL/RESET button on the steering wheel repeatedly the multi-information tire pressure. 3.Press and hold the SEL/RESET button on the steering wheel for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multiinformation display. 4.Select ''RESET'' by pressing the INFO ( / ) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to ''100.'' If you want to cancel the oil life reset mode, select ''CANCEL.''
Turn the ignition switch to the ON (II) position.Press the select/reset knob repeatedly until the engine oil life indicator is displayed.Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.Press the select/reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to "100."NOTE: After the engine oil life and maintenance item codes start to flash (blink) you must RELEASE the reset knob and press again for another 5 seconds. It will then reset.
You can reset your engine light by bringing the oil life display onto your monitor. Hold the scroll button in until the oil life goes to 100 percent. The engine light should go off.
There is no symbol for low oil. If the oil pressure gauge is not faulty and you loose oil pressure you will have a catastrophic engine failure. As described in the owners manual - You must periodically check your engine oil level on the dipstick under the hood. The only symbol that appears on the gauge cluster denotes that the oil life management system has calculated that it is time to change the engine oil. www.trailvoy.com Trailblazer enthusiasts forum
turn the key to on position, dont start it, then press the gas pedel three times with in seconds,turn the car to off position. then start the car it should go of in seconds, it may take a couple of time to get it right. hope this helps ENGINE OIL LIFE SYSTEMHOW TO RESET THE ENGINE OIL LIFE SYSTEMThe Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL SOON message being turned on, reset the system.After changing the engine oil, the system must be reset as follows:# Turn the ignition to "RUN", with the engine off. # Press the "information" and "reset" buttons on the DIC at the same time to enter the personalization menu. # Press the "information" button to scroll through the available personalization menu modes until the DIC display shows "OIL-LIFE RESET". # Press and hold the "reset" button until the DIC display shows "ACKNOWLEDGED". This will tell you the system has been reset. # Turn the key to "LOCK". If the CHANGE OIL SOON message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the reset procedure. this it the actical reset procedure from alldata pro
when you have it on the message that says engine oil life xxx press and hold the clr button and it will reset back to 100%