what is the engine torque spec for 1.6 Opel monza
in sequence torque bolts to 20nm, then again in sequence turn a futher 120 degrees, and again in sequence 120 degrees.
torque for head bolts 3 size diferent and rods
Torque sequence------------ l 93157 l l 862410 l ------------ Step 1: torque in sequence to 44 Ft/LBS Step 2: in sequence completely loosen all bolts Step : retorque all bolts in sequence to 44 Ft/LBS Step 4: in sequence turn an additional 90 degrees Step 5: in sequence turn an additional 90 degrees Recheck final torque in sequence***CAUTION*** engine uses Torque To yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.
What are the torque specifications and the tightening sequence of the cylinder head bolts on a 1996 Saturn SL1?
18 ft lbs in sequence then 90degree in sequence then 90degree in sequence then 90degrees in sequence
torque, in sequence, to 35-40 ft-lbs, then repeat at 65-70 ft-lbs in sequence.
NOTEStep 1: Tighten all bolts to 22 ft. lbs.Step 2: Tighten all bolts to 51 ft. lbs.Step 3: Loosen all bolts, in reverse torque sequence, by 180°Step 4: Loosen all bolts, in reverse torque sequence again by 180°Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs.Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs.Step 7: Tighten all bolts, in torque sequence, by 80-90°Step 8: Tighten all bolts, in torque sequence, again by 80-90°
{| |- | NOTE Step 1: Tighten all bolts to 22 ft. lbs. Step 2: Tighten all bolts to 51 ft. lbs. Step 3: Loosen all bolts, in reverse torque sequence, by 180° Step 4: Loosen all bolts, in reverse torque sequence again by 180° Step 5: Tighten bolts #1 and #2, in the torque sequence, to25 ft. lbs. Step 6: Tighten bolts #3,4,5 and #6, in the torque sequence, 11 ft. lbs. Step 7: Tighten all bolts, in torque sequence, by 80-90° Step 8: Tighten all bolts, in torque sequence, again by 80-90° |}
torque head bolts and order ford 1997 2.0L picture if avalible please
Tighten the cylinder head bolts in three steps using the sequence provided : ==== ==== # Step 1- Snug tighten M12 cylinder head bolts, in sequence, to 34 N·m (25 ft. lbs.) and M8 bolts to 20 N·m (15 ft. lbs.) torque. # Step 2- Tighten M12 cylinder head bolts, in sequence, to 54 N·m (40 ft. lbs.) and verify M8 bolts to 20 N·m (15 ft. lbs.) torque. # Step 3- Turn M12 cylinder head bolts, in sequence, 90 degrees and tighten M8 bolts to 34 N·m (25 ft. lbs.) torque.
The torque specs for a Cadillac depend on which engine it has. For most 425, 572, 368, and 500 engines, the torque for the head bolts is 115 ft. pounds. The torque for the cam bolts is 25 ft. pounds, and the torque for the valve covers is 10 ft. pounds.
The torque sequence for a single cylinder Briggs and Stratton engine horizontal shaft head is increments of 2's for hp and 1's for head bolts. That makes 11 head bolts for an 18 hp.