0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What's the best lug wrench?
The best lug wrench is the cross shaped type with 4 different sockets. This is the only hand wrench that will apply enough torque on your lug bolts.
What are the torque specs for cam bearing bolts 1993 Toyota 3vze v6?
12 ft/lbs but its better to use 1/4" torque wrench set at 144 in/lb so you don't over tighten.
What do you torque the intake manifold to heads on a 98 Chevy silverado 350?
I was searching for the same thing and came accross a site called "torkspecs.com" they say 33 ft/lbs but I want to make sure myself since it is a Auminum intak.e. I hope this is help to you. No more than 35 ft/lbs. To be very accurate with the torque, use a 3/8 drive torque wrench not a 1/2 drive. The 1/2 inch drive torque wrench is long and designed to torque bolts that are at least 1/2 inch in diameter and require at least 60 lbs of torque. The intake manifold bolts are 3/8th with a flange. If you lose a bolt be sure that you use only flanged bolts. A flange bolt is a bolt with a molded flat washer. In my experience in the trade of rebuilding engines, never use a 1/2 drive torque wrench to tighten bolts under a 1/2 inch in diameter. FYI the term (drive) is the size of the square part of the socket and socket wrench. Available in 1/4, 3/8, 1/2, 3/4 and ect.
What size wrench fits an inch and a quarter bolt?
A 1 1/4" wrench will fit a bolt of the same size .
What are the different types of torques?
There are various kinds of torques involved in opeartion of a motor:-Starting Torque: At the starting, motor has to deal with standstiill condition, this torque should be good enough to deal with friction and windageLoad Torque: It is the torque which a motor faces on apply of load.Breakdown Torque: more than this torque if more load is applied on a motor, torque generated will not increase and motor will starts slowing down
What are the cylinder head torque specificatins for a 3.3 2001 dodge grand caravan V6?
Tighten the cylinder head bolts 1-8 in the sequence shown. Using the 4 step torque turn method, tighten according to the following values:Step 1: Bolts 1 - 8 to 61 Nm (45 ft. lbs.)Step 2: Bolts 1 - 8 to 88 Nm (65 ft. lbs.)Step 3: Bolts 1 - 8 (again) to 88 Nm (65 ft. lbs.)Step 4: Bolts 1 - 8 turn an additional 1/4 turn. Do not use a torque wrench for this step.NOTE: Bolt torque after 1/4 turn should be over 122 Nm (90 ft. lbs.) . If not, replace the bolt.
What is a 6mm Allen wrench key?
about 1/4 inch
What are the head bolt torque specs on a 2002 Chrysler Voyager?
2.4L * First All to 34 N·m (25 ft. lbs.) * Second All to 82 N·m (60 ft. lbs.) * Third All to 82 N·m (60 ft. lbs.) CAUTION: Do not use a torque wrench for the following step. * Fourth Turn an additional 1/4 Turn, 3.3L, 3.8L * Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.) * Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.) * Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.) * Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
What are the torque specification for the head bolts for a 2001 Chrysler LHS 3.5L engine?
Using the 4 step torque-turn method, tighten according to the following values: - First All to 61 Nm (45 ft. lbs.) - Second All to 88 Nm (65 ft. Lbs.) - Third All (again) to 88 Nm (65 ft. lbs.) - Fourth + 1/4 Turn. Do not use a torque wrench for this step. NOTE: Bolt torque after 1/4 turn should be over 90 ft. Lbs. in the tightening direction. 1f not, replace the bolt.
What are the torque specs for the head on a 1999 Plymouth Grand Voyager with a 3.3L V6?
* Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.) * Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.) * Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.) * Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
What is shaft power and how is it different from torque of a motor?
Fundamentally: power = torque x rpm Power and torque both make noise, but they are different in how they are measured and what they mean. Torque is not related to time. Power is a time-related rate. Most engineers talk about torque when they need to understand how much force is applied from a dead stop. It is force X radial distance. Huge torque may have very little power (in HP or Watts) behind it. Imagine a really strong guy with a really long wrench unfastening a bolt. He can develop lots of torque, but ultimately he can put out very little power (about 1/4 HP or 185 W for humans) over an extended time.
What is the torque wrench settings for a vauxhall astra 1.4 1992?
STAGE 1 - 25NM STAGE 2 +60 DEGREES STAGE 3 +60 DEGREES STAGE 4 +60 DEGREES ALWAYS USE NEW BOLTS
