0
We do not use transitors from 4 to 10 ohms. We use resistors.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Can you run 4ohm resistor to make 4 ohms speakers 2 ohm?
Yes, you can safely use a 4 ohm amp with one 8 ohm speaker, but you will not achieve full power. The 4 ohm amp is designed to supply a certain voltage into a 4 ohm speaker. Supplying that same voltage to an 8 ohm speaker will result in half the power, or -3dB. For maximum power, use a 4 ohm speaker, or two 8 ohm speakers in parallel.
The resistance of a 4 ohm resistor and a 12 ohm reisistor connected in series is?
16 ohm, R1 + R2+R3 = RT in series.
What is the significance of hybrid model of a transistor?
Use of h - parameters to describe a transistor have the following advantages. 1. h - parameters are real numbers up to radio frequencies . 2. They are easy to measure 3. They can be determined from the transistor static characteristics curves. 4. They are convenient to use in circuit analysis and design. 5. Easily convert able from one configuration to other.
How to identify a 470 ohm resistor?
Resistors are color coded to denote the value of the resistor as well as the multiplier. In your case a 470 ohm would be colored as Yellow Violet Brown corresponding to 4, 7 and a multiplier of 10^1.
What is the best setting for a peavey windsor half stack when you have one speaker that can handle 16 ohm and you can choose from 4 8 Stereo 2 cabinets and 16 ohm without blowing out the speaker.?
Windsor has a three way impedance switch, 4, 8 and 16. Use the 16.
Can you use 10 ohm speakers with a 4-8 ohm receiver?
You can use your so called "4 to 8 Ohm's output" amplifier for your 10 ohms loudspeaker. All amplifiers have an output impedance of less than 0.5 ohms. You use impedance bridging when you connect the 10 ohm's loudspeaker. The "4 to 8 Ohm's output" means only that a 4 to 8 ohm loudspeaker will be adequate and not that the output impedance is 4 to 8 ohms! Scroll down to related links and look at "Impedance bridging - Wikipedia".
Can you use 4 ohm speakers on a 8 ohm system?
yes
What is the resistance of a parallel circuit with resistances of 2 ohm's 4 ohm's 6 ohm's and 10 ohm's?
R = 1/[1/2 + 1/4 + 1/6 + 1/10] Add up the reciprocals of the resistances, and take the reciprocal of the answer.
What is better 4 ohm or 8 ohm amplifier?
Sorry, but there is really no 4 ohm or 8 ohm amplifier. We use only voltage bridging. Scroll down to related links and look at "Interconnection of two units".
Will using a 2 ohm 1200 watt amplifier be ok to use with three 4 ohm speakers 12 and 2-10?
If you connect three 4 ohm speakers in parallel, the amplifier would see a load of about 1.3 ohms. This definitely could damage the amp if you drive it too loud.
What is the ohm's on Chevy Colorado speaker?
4 Ohms. Can use any standard 4 Ohm speaker as long as you don't chassis ground it.
Is an 8 ohm sub woofer better than a 4 ohm sub woofer?
no the higher the ohm the more resistance in the speaker the lower the resistance the more power it will use so if they are the same make the 4 ohm should be louder
Can you run 4ohm resistor to make 4 ohms speakers 2 ohm?
Yes, you can safely use a 4 ohm amp with one 8 ohm speaker, but you will not achieve full power. The 4 ohm amp is designed to supply a certain voltage into a 4 ohm speaker. Supplying that same voltage to an 8 ohm speaker will result in half the power, or -3dB. For maximum power, use a 4 ohm speaker, or two 8 ohm speakers in parallel.
Is 4 ohm better than no ohm?
Don't know if 4 ohm is better than no ohm. I know that 4 dollars are better than no dollars.
How can three resistors of 2 ohm 3 ohm and 4 ohm be connected to give a total resistance of 4 ohm?
2 in series with 3&4 in parallel
What size amp do i need for two 10 inch kicker comp's?
You could go with a 600 watt 2 ch amp or a 300 watt mono block amp, depends on what OHM the subs are, if they are 8 ohm you could wire them down to 4 ohm or if they 4 ohm u could wire them to 2 ohm, i have a 600.1 Boss amp and subs are wired together at 2 ohm and they BANG.
Why use a 500 ohm power resistor?
500 ohm resistance is widely used to convert 4-20 ma current signals generated by a wide range of sensors into voltage signals. It provides 2 to 10 volts to the device. E=IxR.
