0
Its used in collector amplitude modulation,Radio frequency recievers ..etc
Wiki User
∙ 14y ago
Wiki User
∙ 11y agoHigh gain
Add your answer:
Earn +20 pts
Why Amplifier of class B has high theoretical efficiency of 78.5 percent?
The Class B amplifier is a push pull amplifier with 78.5% efficiency. The high efficiency is due to the absence of power consumption during idle time which simultaneously increases the efficiency.
What are the least efficient of class of amplifier?
class b amplifiers as for class b amplifier the 'Q' point is near to cut of region.
Why the name push pull is given to class B power amplifier?
Because two amplifiers are used to accomplish class B power amplifier. One is used to push the current and the other one is used to pull the current. These two amplifiers are almost same but one is connector supplied and the other one is emitter supplied.
How is transformer saturation avoided in class B push pull amplifier operation?
In class B amplifier no DC biasing required, thus lack of of DC current in inpunt and load, saturation of core avoided
What is A or C biasing?
The three standard forms of analog amplifier biasing are:class A - the amplifier is biased in the center of its linear operating range, this is the most linear but least efficient type of amplifier (because the transistors or tubes are always conducting, even when there is no signal to ampliify).class B - the amplifier is biased at the cutoff point, this is an efficient amplifier but is only linear if operated as a push-pull amplifier (because the transistors or tubes are in cutoff and not conducting when there is no signal and through one half of every cycle, a class B push-pull amplifier has two sections that operate on alternate halves of the cycle).class C - the amplifier is biased in hard cutoff so that only the peaks of the input signal are amplified, this is the most efficient amplifier (because the transistors or tubes may be in cutoff and not conducting for more the 85% of the time) but it is not capable of linear amplification. An amplifier biased as class C is only suitable for use in RF transmitter power stages, where a resonant LC tank circuit will be excited into oscillation by the output of the amplifier and complete the missing parts of the cycle.There are other forms of biasing (e.g. class AB) analog amplifiers that get some of the advantages of two of the standard forms. There are also forms of amplifiers having other nonstandard classes (e.g. class D) that are not analog amplifiers, but instead operate by amplifying pulses.
What are the system applications of a class B amplifier?
Class B operated amplifier is used extensively for audio amplifiers that require high power outputs. Its also used as the driver and power amplifier stages of transmitters.
Applications of push pull class B amplifier?
nthing
Is pull push amplifier is known as class b amplifier?
No, a push-pull amplifier can be built class A, class AB, class B, or class C depending on application.class A push-pull is used for low power audio usuallyclass AB push-pull is used for high power audio usuallyclass B and class C push-pull is used for very high power radio usually (B is typical for AM and C is typical for FM)
Which amplifier has more efficiency than class b amplifier?
Class C amplifier.. A class D amplifier is more efficient than class B, and is more efficient than class C as well.
Why Amplifier of class B has high theoretical efficiency of 78.5 percent?
The Class B amplifier is a push pull amplifier with 78.5% efficiency. The high efficiency is due to the absence of power consumption during idle time which simultaneously increases the efficiency.
What are the least efficient of class of amplifier?
class b amplifiers as for class b amplifier the 'Q' point is near to cut of region.
What is a advantage of class B amplifier?
class b amplifier is in between of a and c.so dont warry abt ds
What is the efficiency of class b linear RF AM amplifier?
the approximate efficiency of a class b linear RF AM amplifier is 35%
What is the main difference between a class 'A' and a class 'B' amplifier?
A class "A" amplifier amplifies the entire waveform, a class "B" amplifier only amplifies the first 1/2 of the wave form. See the images in the related link.
What is Class b power amplifier?
When we get amplifier output current for 180 degrees of input. then it's called B class amplifier. In a push pull class B amplifier one of the two power transistors or other amplifying elements handles the positive half of the waveform and the other element handles the negative half of the waveform. In practice, push pull audio amplifiers are usually class AB; each power transistor handles slightly more than 180 degrees of input. This minimizes distortion (crossover distortion) when one of the two transistors ceases output and the other takes over.
Why you use pushpull complementary symmetry for class B power amplifier?
Because the output device in a class B amplifier are biased at cutoff, they only amplify one half of the input waveform, so a complementary stage, biased at class B, is needed to output the other half. There are several circuit layouts to do this.
What are the basic types of amplifiers?
based on i/p:a) small signal amplifier b) large signal amplifierbased on o/p:a) voltage amplifier b) power amplifier c) current ampbased on bandwidth:a)untuned amp(wideband) b)tuned amp(narrowband)based on biasing condition:a)class A amp b) class B amp ......e)class D amp f) class s ampbased on no. of stages:a)multistage amp b) single stage amp
