Fiat do not issue torque settings for a punto they use angles so that you can snap your stretch bolts! after contacting fiat and haynes neither of them would give proper torque settings, so i delved into my many tech manuals on fiat fire engines which is what is in your punto and i have successfully changed many fiat punto head gaskets using the following torque settings: stage 1 starting from the centre head bolts tighten to 33nm: stage 2:65nm and finally stage 3: 96nm these torque settings work fine and will probably save you buying new head bolts.
The torque settings for a 96 Fiat Punto 12cc for cylinder head bolts are 30 NM at 90 degrees. Then an additional 90 degrees.?æ?æ
Punto 1.2 engine code 176A7.000 Torque Stage 1. 20Nm Stage 2. 30Nm Stage 3. + 90 degrees Stage 4. + 90 degrees.
20nm 40nm 90degrees 90degrees
30nm 90degrees and then another 90degrees
The Fiat Uno 1.1 Fire (Fully Intergrated Robotic Engineering) motor is the same in the Fiat Punto 1.1. The torque settings as per Autodata is Camshaft carrier cap - M8 x 1.25 20Nm or M8 10Nm Camshaft gear - 70Nm Anything else, just ask
Uno 1100 cylinder head? 30nm 90degrees then another 90 degrees
It is important to know the head bolt tightening sequence and the torque of a vehicle. For the Fiat Punto it is 20nm, 30nm, 90 degree turn, 90 degree turn, then in order 8,6,2,5,10,7,3,1,4,9.
Fiat Punto was created in 1993.
firstly tighten in sequence to 20Nm all round, then tighten to 30Nm all round,then tighten 90 degrees all round, and finally tighten a further 90 degrees all round. good luck!.
The Fiat Punto is manufactured by the company Fiat. Fiat is an Italian manufacturing company. The manufacturing of the Fiat Punto started in 1993 and is still currently being produced.
No its different
Fiat Punto 1.9l ltd service manual?
No they are not same, though they have fiat punto before them. The new fiat has brought a lot of changes to make it perfect for long drives n here goes it. 'The new FIAT PUNTO2012' .
What is the mains and big end bearings torque setting for uno 1100 engine
i asume you know your spanners so yes it is a straight forward job. and to help you on your way the torque settings are Fiat Punto Fire engine Stage 1 30Nm/22LBf ft Stage 2 59Nm/43.5LBf ft
Number 1 cylinder is at the left hand side if viewed from the front of car, i.e. the timing belt end
i asume you know your spanners so to help you on your way the torque settings are Fiat Punto 55/60 1.1/1.2 engine make sure you use new bolts ect. Stage 1 30Nm/22LBf ft Stage 2 59Nm/43.5LBf ft Punto 55 engine code 176A7.000 Torque figures stage 1. 20 newton metres stage 2. 30 newton metres stage 3. + 90 degrees stage 4. + 90 degrees torque sequence 8 6 2 5 10 7 3 1 4 9 bolts 9 & 10 are the flywheel side of the engine
1. what is the problem of fiat punto front suspension 2. what is the mantinance of fiat punto front saspension
Fiat Punto car parts can be purchased at various retailers dealing with car parts. One can find Fiat Punto parts on the eBay and Breakeryard websites.
You have not told us for what bolt or nut ?. There will be almost a whole page of torque settings for that vehicle. Oilpan bolts may be as little as 12 while cylinder head bolts will be around 70 . We have no clue unless you name the bolt.
where is the fuse for the heater motor ina fiat punto grande 1.2
Fiat punto power steering reservoir on a y reg were can i find it
fiat punto firing order 1342 from timing belt end