Have access to a haynes or chilton manual? they list the torque specs in each of these manuals. If not, they usually cost about $12 at your local auto parts store, or maybe even they have a manual w/o the plastic on it, you could take a glance. Most auto shops when called will kindly provide you with the specs also.
In SI, torque is measured in newton metres (N.m). The percentage torque varies according to the design and specifications of a motor.
torque specs on the bolts that hold the rockers on a 4.9 cadillac motor
what is the torque specs to a 2002 Chevrolet Malibu 3.1 liter motor. Need head and intake torque specs. and sequence.
A lot of manufacturers use a torque setting, but not Chevy. With the motor running, go to zero lash, and then 1/2, to a full turn from there.
Torque specifications are different from motor to motor. These specifications state how tightly the head bots are to be installed. Correct torque insure that the head gasket is sealed properly and correct torque sequence insures that the head itself is not warped in the installation process. Refer to a engine repair manual (Chilton's, Hayne's, etc.) for your vehicle/motor for the correct specs and torqueing sequence. You can usuall find these manuals at your local auto parts store. Hope this helps.
Bolt pattern and torque specs are here: http://toyota.offroadforum.cz/aarc.epnet.com/application/8578/8578R03_Cylinder_Head.html
DC Motor Specifications: 1.RPM 2.No-heap Speed 3.Slow down Torque 4.Most extreme Current
Load torque is the torque required by the load and motor torque is the torque available at the shaft of the motor.
The motor specifications of the Razor E200 Electric Scooter are as followed; 24V (two 12V) sealed lead acid rechargeable battery system with battery charger included, speeds up to 12 mph with high torque chain driven motor.
1996 chevy c1500 pick up 305 motor bolt torque spec intake manifold
Rocker is used to adjest the place of brushed
how to calculate hydraulic motor torque
Check here at: www.60degreev6.com They have all kinds of information and specs on all types of 60 Degree V6's which is the motor that your Corsica has in it. If you have the roller rocker arms, they are 17 ft. lbs.
it varies from motor to motor the rods are any where from 100 - 150 in a kit. then you need to find someone to put them in. you may just need to re torque the rocker arms
what year? what motor?
There are various kinds of torques involved in opeartion of a motor:-Starting Torque: At the starting, motor has to deal with standstiill condition, this torque should be good enough to deal with friction and windageLoad Torque: It is the torque which a motor faces on apply of load.Breakdown Torque: more than this torque if more load is applied on a motor, torque generated will not increase and motor will starts slowing down
go to your local library and see if they have the motor or car manuals with that info.
Every application is different, you will need to look up the torque values for your engine serial number
Electrical motor specifications describe the characteristics of the motor. They are seen on the nameplate of a motor. See the PDF file of the link below for a good description of them.
Honda SI's motor is inline 4 cylinder engine that produces 197 bhp. The motor produces a baseline of 139 foot pounds of torque. The motor is ideal for an economy gas powered vehicle that produces enough power to be considered "fun to drive" as well.
Increasing flux, torque of the dc motor will be increased and speed of the dc motor will be decreased as speed of the dc motor is inversely proportional to that of the flux and the torque of the dc motor is directly proportional to the flux.
speed is directly proportional to the negative of torque in dc series motor..
Max torque and breakdown toarque are the same...,.the point at which a motor will stop/stall.
The torque specs for the different parts of the motor will all vary from each other, and also vary between builds, especially if the engine has been rebuilt, so the numbers provided are averages. The stock rods will come with 40 foot-pounds of torque, the main bolts will come with 90 foot-pounds of torque, the exhaust at 35 foot-pounds, and the valve covers at 10 foot-pounds.Ê
torque of synchronous motor with out feild exitation