Plymouth Voyager
Nissan Xterra
Timing Belts and Chains

What are timing marks for 1989 Plymouth Voyager?

141516

Top Answer
User Avatar
Wiki User
Answered
2009-04-06 11:20:27
2009-04-06 11:20:27

the marks are very vague and hard to see, the timing is a little more complicated than some this size. Its supposed to be 10 degrees out and the cam has an awkward hole that has to be straight up. the other timing marks on the intermittent and the crank should be facing each other, still the marks are hard to see on them so be careful and good luck. If you add chalk to where the timing marks are on the crankshaft with chalk and wipe the excess off, this will make the timing marks easier to see. The marks are recessed in the crank and the chalk will fill them up. Hope this helps you!

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


timing marks 1993 yoyota Camry 2200

there are no timing marks on a timing belt. the marks are on the timing gears and yes you can find the pictures needed in a workshop manuel

had sex too much and got kidnapped

The firing order for a 1989 Plymouth Voyager V6 3.0L is 1, 2, 3, 4, 5, 6. The number one cylinder is on the front left side of the engine.

On the harmonic balancer/driverside

WHATS THE TIMING MARKS ON 93 MAZDA 929

This is not an easy job. Get a manual on your car and it will help on the next repair.

It is screwed into the exhaust manifold on the rear of the engine.

on my 98 heater hoses are at the firewall to the right as you go under the hood. voyager have a tendency to clog up heater cores

where are timing marks on 89 ford probe 4 cylinder I have the bottom not the top

They are on the harmonic balancer but are they on the drivers side or on the passenger side?

I have a 1989 Plymouth Voyager and the computer is located under the hood on top of the drivers' side wheel well. It is inside the plastic housing that feeds air to the air cleaner. The air flow to the air cleaner keeps it cool.

Not with all four wheels on the ground. The front wheels need to be off the ground.

Help...can anyone point me in the direction of a diagram or instructions? online?

If memory serves me correctly, the timing marks will be behind the timing belt cover. There will be marks on the gears and also marks on the block. Line the top gear with the top mark and the bottom gear with the bottom mark. Please note that you will need to undo the battery for a few minutes and then reconnect. This allows the computer to reset itself. Hope this helps

Timing marks? There is a timing mark on the main crankshaft pulley as well as marks on the timing belt cover to line it up with. There is also marks on the cam gear, with the #1 and that arrow being most important, as well as an arrow or other mark on the cylinder head to line it up with. All of these need to line up in order for the timing to be correct. Then the distributor can be moved left or right to fine tune the timing to spec.. -Shaun

There typically isn't any timing marks at the distributor. It is possible to slightly advance or retard the ignition (spark) timing by rotating the distrubitor but as far as timing marks go, the only that you will find will be right above the camshaft sprocket and the harmonic balancer (crankshaft pully). possible one more for the oil pump or countershaft.

unhook - side of the battery and let set 5 mins and reconnect and the light will go out.

Marks are grooves that are cast into the camshaft sprocket and rear cover. crankshaft pulley has notch must be aligned with 10 degree btbc mark (metal plate with #'s) before timing belt is removed


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.