What could causing the heat gauge to be going up and down?

The window goes down easier because gravity is helping. The window tracks could be dirty or the motor could be weak, causing the trouble going up.

If you temperature gauge is going up and down then you may have a problem with your sensor. You should take your car to a professional to ensure that you don't overheat your car.

it could be your fuel sending unit or the float in the tank less likely your gauge is bad but that could also be the problem

Could be low on coolant (leak somewhere) or the thermostat is faulty.

it slows it down because frition is causing pressure for it stop going

Could be, sticky thermostat or low coolant level.

I am having kinda of like that same problem. my gauge reads fine till i get to approx. 1/4 tank. from there it bounces around going up and down not reading really anything. i have no idea what could be wrong.

When you start moving you increase the air flow through the radiator and increase the amount of coolant being pumped by the water pump. Therefore the temperature goes down. You're going to need to figure out why the temp. goes up when stopped. Could be low coolant. Could be partially plugged radiator. Could be bad electric fan clutch. Could be many things.

hi if ur gage keeps dropping and u run out of juice in ur battery it could be one of two things 1) bad battery or 2) bad alternater

It is usually caused by a couple of things,first cause is when slowing down the engine drops in RPM's thus causing your alternator to have a reduce charge output to the battery.Second cause could be indicative of a failing alternator.Best thing to do is have the alternator output checked. Good luck.

Could be your thermostat or your anti-freeze

The largest EVER made was a 2 gauge. It holds a 2 pound metal ball, if I remember correctly. According the gauge index, a 2 gauge shotgun would hold two half pound balls since the diameter of the shotgun tube determines the gauge, the number of balls to equal a pound going down the barrel in this case would only be two to make a pound. Whereas in a 12 gauge, it takes twelve lead balls of the barrel size to make a pound. A two pound meal ball going down the tube would make for a .5 gauge.

In my experience with my Chevy it was a ground wire

Zeus could throw lightning bolts down to earth causing storms.

Not sure how old this posting is but the problem could be the lower intake gasket. I just had mine replaced. If its not under warranty the dealer said it would cost $800.

your coolant level could be low

Sounds like the alternator is going bad, Need to check charging system with a volt meter.

No. The common, plain old, earring size is almost always 22 Gauge. 16 Gauge is just a bit smaller than the common piercing size of 14 Gauge. The size chart goes down in increments of two from 22 usually down into the negatives of 00 gauge, and then breaks down into diameters.

Your gauge could very well be bad, many pools that we took care of the gauge on the filter was bad, after backwashing the filter just check any of you lines going back to the pool and your should notice the pressure is a lot higher. A lot of people just check the flow by placing there hand at an outlet to check pressure than by walking over too the filter and reading the pressure, instead of buying a new pressure gauge.

i get abdominal quaking when i sing and feel like im going to fall down and general tremor starts what can i do?

a number of things could cause this but the first thing that comes to mind is tires out of balance or out of round. Could also be an alignment issue.

The temp. gauge on the side of the water heater is obviously set too high causing this problem. Turn down the heater until the problem is solved.

In the early to mid 1960's is as far as I could narrow it down to.

This sounds like it could be your speed setting, but in all likelihood, you are not going deep enough with the liner. It could also be a combination of the two. The setting of your contact screw will also play a part in the overall packing ability of your machine.

There are several reasons that the rpm of a power generator is going down. The rpm going down could cause damage to the motor if it is not fixed. To find the exact reason why this is happening review your user manual.