0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What two sub folders in the cWindowssystem 32 folder contain files needed for Windows startup?
C:\Windows\System32\config and C:\Windows\System32\drivers
What command do you type to save the configuration stored in RAM to NV RAM?
Router(config)#Copy running-config startup-config
How do you figure out a subnet mask from an IP address?
go to Start than click run than type command.com or cmd.than type config or config /all
How do i access computer config?
In windows 8/ 10, search for and run the file "MSCONFIG"
How can an IP address for a network device be assigned to a particular network?
Router(config)# hostname AdminAdmin(config)# enable secret cangetinAdmin(config)# interface fa0/1Admin(config-if)#ip address 192.168.1.22 255.255.255.248Router(config)# hostname AdminAdmin(config)# enable password cangetinAdmin(config)# interface fa0/1Admin(config-if)# ip address 192.168.1.22 255.255.255.248Router(config)# hostname AdminAdmin(config)# enable secret cangetinAdmin(config)# interface fa0/0Admin(config-if)# ip address 192.168.1.22 255.255.255.248Router(config)# hostname AdminAdmin(config)# enable password cangetinAdmin(config)# interface fa0/0Admin(config-if)# ip address 192.168.1.22 255.255.255.248
Where do startup-config and a running-config reside in Cisco equipment?
startup-config resides in NVRAM and running-config resides in RAM.
Which command is used to upgrade an IOS on a Cisco router?
config tftp run
Configure NAT to allow PC3 to ping PC1?
R3#configure terminalR3(config)#access-list 104 permit ip 10.0.0.128 0.0.0.127 anyR3(config)#ip nat inside source list 104 interface Serial0/0/0 overloadR3(config)#interface fastEthernet0/1R3(config-if)#ip access-group 104 inR3(config-if)#ip nat insideR3(config-if)#exitR3(config)#interface Serial0/0/0R3(config-if)#ip nat outsideR3(config-if)#exitR3(config)#interface Serial0/0/1R3(config-if)#ip nat outsideR3(config-if)#endWriting by vanhuuvt32bonphuonglanha@gmail.com
What are Two subfolders in the CWindowssystem32 folder that contains files needed for Windows startup?
C:\windows\system32\drivers and c:\windows\system32\config
What is the command to remove the console password router?
Remove Console password router>enable router#configure terminal router(config)#line console 0 router(config-line)#no login router(config-line)#no password router(config-line)#exit router(config)#exit
What is the purpose of Copy run start command on a Cisco router?
It is short for copy running-config starting-config. Running-config is the configuration of the router as you have modified it and which is currently operating, held in RAM (gone after a reboot), and you copy it to the starting-config which is in NVRAM and gets loaded by the router when it boots/ So essentially you're saving what you have now to the persistent storage so your router will still work after a reboot.
How do you configure RIP routing protocol on a Cisco router?
Here is a basic overview of the configuration of RIP on a Cisco router:Router(config)#router ripRouter(config-router)#network 192.168.1.0Router(config-router)#network 192.168.2.0Router(config-router)#network 192.168.3.0Router(config-router)#network 192.168.4.0Router(config-router)#network 192.168.5.0The 192.168.x.0 address can be changed to whatever address you would like to be broadcast over RIP. There are also other settings that can be configured.If you use RIPv2 you can also have the following configuration:Router(config)#router ripRouter(config-router)#version 2Router(config-router)#network 192.168.1.0Router(config-router)#network 192.168.2.0Router(config-router)#network 192.168.3.0Router(config-router)#network 192.168.4.0Router(config-router)#network 192.168.5.0Router(config-router)#exitRouter(config)#exitRouter#%SYS-5-CONFIG_I: Configured from console by consoleRouter#copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]Router#
