Head Gaskets and Valve Covers
Pontiac Le Mans
Pontiac Sunbird

What do the head bolts on a Pontiac sunbird torque at?

222324

Top Answer
User Avatar
Wiki User
2006-01-22 02:33:21
2006-01-22 02:33:21

autozone.com current vehicle upper left choose car repair info vehicle repair guides hope u find it from there

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

A 1993 Pontiac Sunbird head bolt torque sequence recommends starting at one and of the head and alternating to the other end of the head. You should end up in the middle.

User Avatar

This is the order for the bolts. I do not know the torque. Assuming that the graph is a top view of the head bolts. --8--4--1--5--9-- --7--3--2--6--10--

User Avatar

The 3800 Pontiac engine had bolt torque specification is 160 pounds. The head bolts should be torqued in 40 pound intervals.

User Avatar

What is the head bolt torque for a 1997 chevy lumina four cylinder?

User Avatar

The short bolt torque specs for the head gasket of a 2000 Pontiac Sunfire is 43 foot pounds. The torque specs for long bolts is 46 foot pounds.

User Avatar

The 1995 Pontiac sun fire cylinder had bolt torque specification is 160 pounds. The head bolts should be torqued in 40 pound intervals.

User Avatar

first get new head bolts. they are torque to yield. torque them to 37 ft-lbs and then rotate an additional 120 degrees.

User Avatar

The 1999 Pontiac Montana 3.4 liter engine cylinder head bolt torque specification is 150 pounds. The cylinder head bolts should be torqued in 50 pound intervals.

User Avatar

The head bolt torque specifications, for your 2002 Pontiac Grand Prix, is 160 pounds per square inch. The head bolts should be torqued in 40 pound intervals.

User Avatar

torque for 2c engine cylinder head bolts

User Avatar

torque setting for cylinder head bolts for a skoda felicia

User Avatar

HEAD BOLT TORQUE For your 1999 PONTIAC GRAND AM: HEAD BOLT TORQUE FOOT POUNDS (FINAL TORQUE) TORQUE SEQUENCE --------- | 6 2 3 7 | | 5 1 4 8 | --------- STEP 1: TORQUE IN SEQUENCE TO 33 FT/LBS STEP 2: TURN AN ADDITIONAL 90 DEGREES RECHECK FINAL TORQUE IN SEQUENCE *** CAUTION *** ENGINE USES TORQUE TO YIELD HEAD BOLTS (TTY) THAT PERMANENTLY STRETCH DURING THE INITIAL INSTALLATION. NEW HEAD BOLTS MUST BE USED WHEN CYLINDER HEAD IS REPLACED OR RE-INSTALLED TO OBTAIN PROPER TORQUE. ALWAYS COAT BOLT THREADS WITH THE PROPER SEALANT.

User Avatar

to what torque must the bolts on the head of a 2000 Hyundai accent be tightened?

User Avatar

Torque specs for a 1995 subaru impreza 2.2 head bolts?

User Avatar

The torque specs for 660 raptor head and hex bolts is about 26 lbs.

User Avatar

which one? The head bolts? Engine to transaxle? And, are you really asking what the tightening sequence and/or torque rating is?

User Avatar

There are either eight or ten bolts on the head of Jinma tractor. The torque bolts require 95 to 105 foot pounds.

User Avatar

For all the 2.3, 2.4L QUAD 4 engines, the head bolts are Torque to Yield. The porper torque value is 30ftlbs PLUS a 90 degree turn of the wrench. The bolts must be new every time ( NEVER REUSE OLD BOLTS). The torque values and proper sequence are including in the box the new bolts come with. BUT honestly, the torque value is 65ft lbs like all GM Chevy motors have been for eons.

User Avatar

You should torque the head bolts by alternating from and to end, working towards the center. The head bolts should be torqued in 40 pound intervals.

User Avatar

Cylinder head to block torque = 80 ft-lbs.

User Avatar

What is the torque spect for head bolts on duramax 6.6


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.