0
What do you do next after you've replaced all the bulbs and the flasher and still no turn signals?
Wiki User
∙ 18y ago
You probably replaced the emergency flasher, so remove it & try your flashers; if they don't work, reposition the flasher & try your flashers. If they work now, then try to locate the turn signal flasher (ref. repair manual). Or...heaven forbid, you have a short or ground in your turn signal wiring harness (somewhere), where only an ohm meter and knowing how to use it will locate it. Good Luck!
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
Why would the turn signals quit working when the hazard lights still work and the flasher and bulbs have been replaced on a 1995 Chevrolet Corsica?
Check the flasher for the turn signals which is under the dash on the left side of the steering column . It is different from the emergency flasher.
What causes front turn signals not to flash and rear ones to flash rapidly on a 1999 olds intrige I have replaced the emergency flasher assembly and it still does it.?
If the turn signals flash quickly, its because a bulb is out. Have you tried replacing the bulbs? Have you verified the replacement bulbs are indeed good? Sounds like a bulb or two may be out. The flasher depends on the bulb's current to set the flashing rate. If a bulb is out (or disconnected for some reason) the flasher usually will flash quickly or not at all.
93 town car that the signals stopped flashing emergency flashers still work you have checked fuses and bulbs help?
The directional signals and the emergency flasher each have their own flasher unit. They are the same type of flasher and should be beside each other under the dash.
I replaced the flasher and my turn signals still don't work on my 1999 Mercury Cougar?
If you replaced the flasher on your 1999 Mercury Cougar and your turn signals are still not working, you should check the turn signal fuse. This fuse is located under the dashboard on the driver's side of the vehicle to the left of the steering column.
1992 Cavalier Turn Signals turn on but do not blink Changed fuse flasher still haven't gotten it to work?
check all your bulbs and fuses
How do you fix it when turn signals do not work but flashers do?
The signals and the emergency flashers have separate circuits, separate fuses, separate flasher relays. Start with checking the fuses, the bulbs, the signal flasher relay and wiring and if it still doesn't work it may be the signal switch is bad.
Your turn signals wont work but how do you know what to fix?
check the bulbs, check the fuse then check the flasher, if they are still dead the signal switch may be at fault.
1991 dodge shadow - replaced the bulbs and turn signal flasher and the turn signals still don't flash what next?
Answer ScottmAKE SURE YOUR FUSES ARE GOOD AND YOUR WIRES ARE NOT BROKEN TO THE SOCKET. CERTAIN DODGE APPLICATIONS WILL MAKE ALL LIGHTS NOT WORK WHEN 1 IS OUT OR BROKEN.
My blinkers come on but won't flash. I replaced the flasher and still won't blink. Yes I am sure I changed the right one.?
Some vehicles has a flasher relay for the turn signals and another one for the hazard lights. Are you sure you replaced the correct one?
1994 cavalier--changed switch bulbs fuses hazards work but turn signals still dont work any suggestions?
have you tried replacing the flasher u need to replace the flasher can for the turn signals there are 2 one for hazards and one for turn signals usually found in the fuse box, and cost about 3 bucks
You replaced the flasher relay but the turn signals still don't work at all Hazards work fine Why?
on the Chevy beretta there are 2 flashers one is right next to the steering column to the behind the plastic dash piece,this is your turn signal flasher replace it and your signals should work.
1995 grand prix only 1 turn signal works 4 ways are fine?
First check all the bulbs. If all the bulbs are good replace the signal flasher relay. If it still doesn't work it may be in the signal switch. The signals and the 4 way have separate circuits, fuses and flasher relays.
