0
Touching a headlight bulb will shorten the life of the bulb considerably. the oils from your skin cause a hotspot on the bulb and shorten the life. Please see the link below for more information.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you replace a headlight in 2000 Honda accord?
It should be a bulb. look behind the light itself. There is a plastic ring you can unscrew by hand. after that, pull the bulb out and replace it. Be careful not to touch the glass of the bulb with your hand. the oils on your skin will cause it to burn out fast.
How do you replace the headlight bulb located on a 1994 Plymouth Acclaim?
the bulb that the car uses is a 9004 headlamp. Locate the wire behind the headlight in the engine compartment. unplug the wire from the bulb.With your hand you will feel a retainer ring that is about two inches in diameter. turn it about a quarter of a turn counter clockwise and it will come off in your hand. Pull the bulb out. Get the new bulb and reverse the process. It is pretty simple, the bulb will only fit one way and so will the wire that attaches to the bulb. Remember, it is very important that you do not touch the bulb(glass part). The oil from your skin will form a "hot-spot" and shorten the life of the bulb considerably.
How do you change headlights on 2007 Mustang?
Headlight Bulb Replacement * If your going to replace the left hand light bulb remove the air filter housing * Disconnect the electrical connector unless replacing the headlight housing * Rotate the bulb holder counterclockwise and pull it out the bulb and holder assembly Headlight Housing Replacement * Remove the front bumper cover * Remove the upper headlight housing mounting bolt and pushpin * Remove the lower headlight housing mounting bolts * Pull out the headlight housing assembly and disconnect the electrical connector
How do you replace a headlight on a 2003 jaguar s type?
Well just the bulb or the whole assembly? If whole assembly, then you must remove ft bump. If bulb only ,depends on engine space and size of your hand, you can gain access to bulb behind headlight assembly.
How do you replace a headlight on a 2003 jaguar s- type?
Well just the bulb or the whole assembly? If whole assembly, then you must remove ft bump. If bulb only ,depends on engine space and size of your hand, you can gain access to bulb behind headlight assembly.
How do you change a headlight in a 1994 300zx?
If you pop the hood, on the back of the headlight housing, there are some wires with a snap on or twist on connection. If you disconnect them as you pull them out the headlight is attached to the other end of the connection. Make sure not to touch your new bulbs with your hands because the glass on a headlight bulb is designed to run at a high temperature, but the oils on your hand get hotter than the temperature they are suppose to operate and will cause them to blow or bust. If you do accidentally touch one, just wash it off with alcohol.
How do you replace the headlight bulb located on a 1995 Chrysler New Yorker?
If you just want to change the bulb,you might be able to reach your hand behind the headlight and twist the locking ring counterclockwise and remove the bulb.you may need to unbolt the headlight housing to make room to replace it.
How do you change the headlight on a 99 Honda Accord?
THERE ARE PLUGS FOR THE HIGH BEAMS AND LOW BEAMS ON MY 99 HONDA ACCORD. Make sure the lights have been off for at least 20 minutes, those halogen bulbs are really hot, trust me. Simply grab the plug directly behind the headlight fixture, turn counterclockwise about a quarter of a turn, and the bulb assembly will come out of the headlight fixture. Once it is out of the headlight fixture, then you will need to unplug the bulb assembly from the electrical wire. To do this, hold the bulb part with one hand, and squeeze the bottom of the middle "lever" of the plastic connector to release the bulb from the electrical wire plug. Next, do not let the new halogen bulb touch your skin, because the natural oils from your fingers and hand will cause the bulb to overheat and the bulb will burn out or explode shortly after use. I have found it easier to do the following. Take the new bulb and plug it into the headlight fixture, remember the orientation or positioning that it came out a little crooked, and you will need to rotate it a quarter turn clockwise and it should lock back into place easily. Then, once the bulb is in the headlight fixture, plug in the electrical wire connector to the bulb. I know on some models the intake vent hose or the coolant reservoir is in the way, but once you get the bulb out, you can unlpug the bulb, and if you put the bulb in first then plug in the electrical wire connection, it should be much simpler for you. Good Luck!
How do you remove the driver side headlight lamp on a 2000 Toyota Celica?
If you can't fit your hand between the headlight and the fuse box to unscrew the bulb, take off the bolts at the top and bottom and the entire headlight unit will come out.
How do you change a Buick rendezvous headlight?
To change a Buick Rendezvous headlight it will be necessary to raise the hood on the vehicle. There is an access panel for changing the headlamp just behind where the headlight is. Remove the panel, then gently turn the old bulb. Insert the new bulb without the hand touching the glass part of the bulb. This can be done through the use of a special pair of pliers made just for this purpose.
How do you remove the headlight module on a 1997 Olds Aurora to allow for bulb replacement?
I read this also in my owners manual for my '97. But I was able to squeeze my hand in and change the bulb without removing the headlight. I changed both bulbs this way and I do not have small hands. Good luck!
How do you change a BMW 325i headlight bulb 2006?
On the passenger side, Remove the headlight cover by flipping the latch. Disconnect the main electric harness. Disconnect the wire harness to the light bulb, you can pull on it. At the top of the bulb you can slide the latch and open it, be careful as the latch will pop out, the bulb should pop out. The driver side is a bit more tricky as there is less room to get your hand inside the headlight assy, just take your time and you can get the bulb out. I loosened the 2 top bolts that hold the headlight assembly to have a little play as I installed the new bulb. It's recommended you do not touch the bulb with your bare fingers. You can use thin surgical gloves or just be careful not to touch the bulb. Put in the bulb, make sure it goes into the slot, by looking thru the headlight. Relatch the clip. I used a mirror and flash lite to see what I was doing. Once you set the clip then install the wire connector. Be sure to test the lights before putting the caps back on and install the mount bolts on the headlight assy and there u go! You've just saved yourself a visit to the dealer and $$$ I just replaced the low beam headlight on my 2006 325i, following the instructions on pages 118-119 in the owner's manual. There is an access panel in the wheelwell. It is removed by turning two round buttons. Underneath there is a cover on the back of the light assembly that snaps off. You then pull the connector off the back of the H7 bulb and push the top of the wire retainer to the right to release the bulb. Replace it the same way. Small hands help.
