Want this question answered?
What is the liquid that leaves the condenser called
Adiabatic cooling happens when air cannot expand or compress. A liquid cooling system uses a special integrated pump, reservoir and a cold plate unit. The process for liquid cooling is long and complicated to fit in a small box. Check out Asetek where you can read the entire process and see a demonstration.
How do you measure Sub-Cooling for a R-22 AC system SUB-COOLING IS THE THE "HEAT BELOW SATURATION". THE SUB-COOLING LEAVING THE CONDENSER IS CALCULATED BY TAKING THE (ACTUAL)CONDENSING TEMPERATURE AND THEN SUBTRACTING (MINUS)THE LIQUID REFRIGERANT TEMPERATURE (USE THE CHART)LEAVING THE CONDENSER.=THE SUBCOOLING. NORMAL SUBCOOLING AT THE CONDENSER OUTLET SHOULD BE 10*F. THIS WILL ENSURE THAT LIQUID WILL NOT FLASH INTO VAPOR BEFORE IT GETS TO THE EXPANSION VALVE, SHOULD THERE BE A SLIGHT INCREASE IN TEMPERATURE OR A SLIGHT DECREASE IN PRESSURE DUE TO A PRESSURE DROP. SUB COOLING INCREASES CAPACITY & PREVENTS FLASH GAS IN THE LIQUID LINE AHEAD OF THE EXPANSION VALVE. I HOPE THIS IS VERY CLEAR, AND HELPS U FIGURE OUT HOW TO MEASURE IT. TODD S. FISCHER, PRESIDENT OF THE TAMPABAY CHAPTER OF RSES THE REFRIGERATION SERVICE ENGINEERS SOCIETY- BECOME A MEMBER SOON!!
A condenser is generally an object made from glass, used to condense a gas to a liquid.
Refrigerant enters the condenser as a high pressure vapor. In the condenser, the heated refrigerant is cooled by transferring its heat to the air which passes through the condenser fins, and it changes state to a liquid during this time.
The function of the condenser is to condense a substance from its gaseous to its liquid state, typically by cooling it.
Pretty simple, it condenses the refridgerant into a liquid (giving off energy as heat) the cooling happens later in the evaporator part where the liquid turns back into a gas (taking the energy from surrounding area, thus lowering the temperature. The condenser turns the refrigerant into a liquid by lowering the volume it is occupying, tightening up the molecules turning the refrigerant into a liquid.
Pretty simple, it condenses the refridgerant into a liquid (giving off energy as heat) the cooling happens later in the evaporator part where the liquid turns back into a gas (taking the energy from surrounding area, thus lowering the temperature. The condenser turns the refrigerant into a liquid by lowering the volume it is occupying, tightening up the molecules turning the refrigerant into a liquid.
A condenser is a form of heat exchanger. In the condenser, the coolant condenses from a gas to a liquid, and loses heat energy to the surroundings (like air being blown across it).
Pretty simple, it condenses the refridgerant into a liquid (giving off energy as heat) the cooling happens later in the evaporator part where the liquid turns back into a gas (taking the energy from surrounding area, thus lowering the temperature.) The condenser turns the refrigerant into a liquid by lowering the volume it is occupying, tightening up the molecules forcing the refrigerant into a liquid state.
what happens when refrigerant enters the condenser
The compressor elevates the boiling point of the refrigerant to a point at which the air (or water) moves across the condenser is low enough to condense the refrigerant to a liquid. Additional passes in the condenser coil cool the liquid refrigerant below its boiling point to ensure it remains a liquid as it experiences pressure drop in its journey to the evaporator. This cooling below the boiling point is called sub cooling
What is the liquid that leaves the condenser called
Condesor- cools the liquid formed gas after compressor compresses. After condensor it pass through the expansion valve, then again liquid formed gas expanses to gas form and produses cooling .this cooled gas then passes through the evaporator coils
Adiabatic cooling happens when air cannot expand or compress. A liquid cooling system uses a special integrated pump, reservoir and a cold plate unit. The process for liquid cooling is long and complicated to fit in a small box. Check out Asetek where you can read the entire process and see a demonstration.
Heat. The condenser acts through cooling with a greater surface area (on the inside of the condenser); the constant fluid flow keeps the temperature down. If you were to assemble the apparatus so that the water flows from top to bottom, the condenser would never fill up, and your reaction will have difficulty cooling down. Risky if you have volatile chemicals or a reaction that you need to keep cool.
How do you measure Sub-Cooling for a R-22 AC system SUB-COOLING IS THE THE "HEAT BELOW SATURATION". THE SUB-COOLING LEAVING THE CONDENSER IS CALCULATED BY TAKING THE (ACTUAL)CONDENSING TEMPERATURE AND THEN SUBTRACTING (MINUS)THE LIQUID REFRIGERANT TEMPERATURE (USE THE CHART)LEAVING THE CONDENSER.=THE SUBCOOLING. NORMAL SUBCOOLING AT THE CONDENSER OUTLET SHOULD BE 10*F. THIS WILL ENSURE THAT LIQUID WILL NOT FLASH INTO VAPOR BEFORE IT GETS TO THE EXPANSION VALVE, SHOULD THERE BE A SLIGHT INCREASE IN TEMPERATURE OR A SLIGHT DECREASE IN PRESSURE DUE TO A PRESSURE DROP. SUB COOLING INCREASES CAPACITY & PREVENTS FLASH GAS IN THE LIQUID LINE AHEAD OF THE EXPANSION VALVE. I HOPE THIS IS VERY CLEAR, AND HELPS U FIGURE OUT HOW TO MEASURE IT. TODD S. FISCHER, PRESIDENT OF THE TAMPABAY CHAPTER OF RSES THE REFRIGERATION SERVICE ENGINEERS SOCIETY- BECOME A MEMBER SOON!!