It doesn't matter on a diamond blade. Either way will work. Usually there is printing on one face that would face out, on the nut side, but it doesn't matter.
NO! Granite is hard S#$!. 1.If you don't have a diamond blade its not gonna do much. It doesn't matter how many blades or which way they turn. 2.You will need water to cool the blade and the tile. Without water to cool it the tile will get hot and break and the blade unless diamond will overheat turn to molten metal and fly apart .
A standard tile cutter with a scribing wheel and breaker wings will do the job nicely, otherwise you can use a wet saw or a hand held angle grinder with diamond cutting wheel too.
Yes, as long as it's not too thick,and fed in slowly to a good water served diamond blade.
Ceramic tile should be cut with a wet saw, or with a tile scoring tool. It is not necessary to wet the tile in either case, as the wet saw will cool the blade and the scoring tool has no blade to cool.
You need an actual tile saw. You can probably rent one at your local hardware store.ANS 2 - Tile is best cut with a water fed saw, or at least one where the bottom of the blade runs through a container of water. Cheap electric tile saws are now common and useful for occasional tile jobs. I bought one 3 years ago for $89 and spent $29 on a reasonable 8" diamond blade. It's lasted me through 8 complete bathroom renos and two tiled kitchen floors. Keeping the blade wet and cool is the key.
No, It will just take the teeth off of the blade. You can buy a blade for your skilsaw though.ANS 2 - Never seen a skilsaw blade that can cut brick safely - but it's easy to do on a tile saw.
To cut ceramic tile, use a tile cutter or a wet saw. With a tile cutter, score the tile's surface using a scoring wheel, then apply pressure to break it along the scored line. A wet saw uses a diamond blade to make precise cuts, with water cooling the blade.
Tile saw, the blade runs in water and is like a small table saw. Cut off saw can use water but usually is dry and is a chop saw. The blade come down into the tile or brick which is in the stationary base.
I have done this. The floor drain for a toilet is round making it difficult to cut, but a professional tiler can cut a curve or circle into a tile using a tile saw and grinder.Mark the tiles circle or curve.Cut straight notches into the tile about a 1/4 inch apart to the part that doesn't go on the floor.Use a grinder with a diamond blade to smooth out the circle. This may take a few settings.Then set the tile.
A wet tile saw can be used in construction as a table saw, as a shredding saw or any type of regular saw. However the wet tile saw is specifically built for the use of water incorporated in the saw machine.
I install ceramic tile professionally in the Opelika, AL area. I have several saws some dry some wet. It depends on what kind of saw you have. Breakers have a tungsten blade that scribes the tile and then breaks it. Wet Saws usually have large blades 10-14" in diameter that need to be wet when cutting. Grinders have small 4-6" blades that cut dry. Hand saws look similar to a skil saw and usually cut dry also. I would recommend sharpening the blade by cutting a cinder block or brick with it. Just dip the blade into the brick or block about 1/2" to 1" about 2 times and it should dramatically improve the cutting ability of the blade. If you are cutting a hard, dense tile and the blade is "dulling", cut through a softer tile to "sharpen" the blade again.
Time was when the tile for a wall or a floor had to be nipped into shape by hand. Nipping is time consuming and messy. All nipped cuts are somewhat less than perfectly curved or straight. Nipping is still often used for curved cuts after the bulk of material has been removed by a modern tile saw. The wet tile saw is a power tool that is the professional’s choice for quick, clean, and near perfect cuts. Cutting any type of tile requires an abrasive. Steel teeth are not up to task of cutting ceramic or stone tile. And because these materials are hard, the cutting device gets very hot. Tile saws use diamonds embedded in a spinning wheel to make near perfect cuts. To keep heat from building up, tile saws use a water bath that cools the blade while it spins. To operate a tile saw, both electric and water supplies are needed. Consequently, tile saws are often set up outside where water sling is not a problem, or they are carefully isolated from any indoor surfaces that may be damaged by water. Pre-manufactured, protective enclosures, known as saw shacks, are available for indoor use. Most saws use a stationary spinning blade and allow the tile to be slid along a fence and by the blade for accurate cutting. On basic saws, the tile slides along the table surface. Other models allow the tile to be clamped to a moveable table which then easily slides the tile past the blade. Either of these styles allows for a miter guide to position the tile at an angle to the blade for off-angle cuts. Miter guides are also useful for making multiple straight cuts to produce the the radius of a curved cut. When purchasing or renting a tile saw, the best choice is the one with the easiest way to move the tile past the blade. For 4.25 inch tile bathroom tile, most any saw is capable. When cutting larger tiles, the conveyance method can greatly affect the accuracy and cleanliness of the cut. The easier It is to move the tile by the blade, the smoother the cut.