0
The bolt could have been faulty, or the torque wrench may not be calibrated.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
Head bolt torque specs and tightening sequence on a 2002 ford focus 2.0 liter single overhead cam?
Go to NAPA and buy a repair manual for your specific car.
What is the head bolt torque pattern for 1998 vw jetta 6-cylinder?
Always torque in zig zag pattern... snug up all bolts first then torque the corners head bolts ( starting at the top left side looking down at the head )then go back up to the top left ,where you orginially started and torque up the next bolt over. Then go to the bottom right and torque the next bolt over from the corner .Then go to the top right and torque one bolt from the corner, then bottom left one bolt from the corner and work your way into the center. Torque the top bolt first when you get to the center ........always remenber when your checking the torque... you check the same way as you installed. Have fun the older vr-6's are the best ones to have... just hard to find parts
What are the head bolt torque settings for Toyota 3y engine?
Torque in three stages 14mm bolt: 34,61 & 88 nm. (25,45 & 65 FT.LBF) Torque 12mm bolts to 19 NM. (14FT.LBF) or go to... go to tercelonline.com the information you seek is there.
What is head bolt torque for Kawasaki mule?
Go to a professional it's easier that way.
What is Chevy 350 Oil pan bolt torque?
You only torque them to 12 ft. lbs. Start in a corner after there all snug and go clock whys torquing them
Looking for torque specs and sequence for a 2000 Chevy Tracker with a 2.0L DOHC head?
there are eight head bolts start by snuging the bolts down then grab a torque wrench starting with the left bolt closest to the front of the engine torque the bolt down at 15lbs then the right side bolt in the far corner then the left side bolt second from the back then the right side bolt second from the front then the bolt straight across from it then the right side bolt second from the back then the bolt in the left side back corner and then to the right front corner bolt then set the torque wrench to 25lbs repeat same pattern and u dont have to but u can set the torque wrench to 28 lbs for a third pass then go over every bolt one last time to make sure they are all the same
What is the torque and torque sequence for the head and rocker arm assembly of a 1986 Chevy Celebrity 2.5L?
you torque the head bolts to 18ft-lbs start in the middle and work toward the outer bolts then reset the torque wrench to 26 ft-lbs and follow the same but as they hit 26 go 1 quarter turn on each bolt This torque sequence for 1986 and 1987 2.5's from the Haynes manual is: Step 1, 18 ft lbs. Step 2, All but bolt 9 22 ft lbs, bolt 9 29 ft lbs. Step 3, all but bolt 9 turn an additional 120 degrees, bolt 9 turn an additional 90 degrees. Bolt 9, when the engine is in the car is the front most bolt on the passenger side.
What is the head bolt torque and sequence on a 1990 Pontiac Le Mans 1.6 L 4 cylinder?
Answer HEAD BOLT TORQUE AND SEQUENCEyour answer is looking from front to back of engine you have ten head bolts to tighen start with 3,8,1,9,5 that's the back bolts now the front bolts there 4,7,2,10,6, now to torque, follow head bolt numbers torque each to 18 foot lbs now there is really no torque for these head bolts , you just start at a 90 degree point and go 60 degrees first time all the way around , then again 60 degrees .. now run the engine a few minutes , then go back and torque all head bolts to 30dgrees ( note very important) that clean all head bolt holes real good , and make shure treades are all clean and in good condition ......
What is the torque specs for the front axle on an 1986 Honda Goldwing?
Torque spec's front axel nut is 44 ft-lb caliper upper bolt 25 ft-lb and lower bolt is 17 ft-lb..............Tighten the axel holder forward nuts first, then the rear nuts. Torque is 18 ft-lb. There you go, right from the book. Good luck.
How do you find the cylinder head bolt torque sequence for a 1989 Chevy 350?
You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
What are the torque specifications for gm 3.4 cylinder head bolts?
44ft lbs on all and then go back an additional 95 degrees. (95 degrees is just over a quarter turn) Make sure you follow the correct torque sequence. That might be a little difficult to explain with out a photo but I will try. There are 4 bolts across the bottom and 4 across the top. If you are standing at the front of the car facing it. Bottom row 2nd bolt from the left. Top row 2nd bolt from the left. Top row 3rd bolt from the left. Bottom row 3rd bolt from the left. Bottom row 1st bolt on the left. Top row 1st bolt on the left. Top row 4th bolt from the left (last one on right) Bottom row 4th bolt from the left (last one on the right) You should always replace your head bolts once you have torque them down to get the correct torque.
What is the torque specifications on the cylinder head bolts for a 1991 ford 302?
IT DEPENDS ON THE HEAD BOLT MFG. STOCK HEAD BOLTS ARE 65 FT.LBS TO 72 FT. LBS! ANY OTHER BOLT YOU TYOU NEED TO GO BY WHAT THEY SAY!
