0
The grounded conductor (Neutral) can be white or gray. The grounding conductor can be solid green, Green with a yellow tracer or bare copper.
Jaycee Emard
Add your answer:
Earn +20 pts
What happens when there is no plastic coating on a electrical wire?
Nothing happens. The wire will still conduct electricity. An example of this is the overhead utility wiring. The insulation on a conductor is there strictly to keep the conductor from touching any thing that would ground the conductor. This grounding could be from another adjacent conductor or a grounded medium around the conductor. A grounded conductor will trip the over current protection and trip the circuit off line. Without an insulation on the wire multiple wires in a conduit could not be utilized.
What is multiwire branch circuit?
A multiwire branch circuit is consist`of two or more ungrouded conductors that has voltage between them and has a grounded conductor that is eoual voltage between each conductor connect to the neutral and it,s ground
What is an grounding electrode conductor?
It is the conductor that is used in service distribution panels that bonds the distribution panel's neutral bus bar to the ground electrode (rod). This brings all of the distribution panel neutrals that are connected to the same supply system to the same potential, that being zero. Should a supply service neutral open this ground wire will maintain the systems integrity until repairs can be made.
What is the purpose of grounding electrical equipment?
It is a safety measure for devices that have a metal case where a failure in the device could cause the case to be connected to the hot side of the circuit. By grounding the case the breaker will trip instead of you getting a shock.
What is the process of bringing a negatively charged conductor in a contact with the earth resulting in the conductor discharging until it is completely neutral called?
The process is called grounding. Many devices need to be grounded, hence the U shaped pin on a devices that make contact with the ground in normal house wiring.
What color wire is a grounded conductor?
Grounded conductor is white 120/240 volt & gray 480 volt. Grounding conductor is green or green with yellow.
Where the ground wire located?
The grounded conductor is usually covered in white or light gray insulation. The grounded conductor is connected to the grounding conductor at one and only one point, usually near the transformer or in the circuit breaker panel.
What color is a grounded conductor?
In house wiring it's typically a bare copper wire. It may occasionally be green.
What is it called when wires connect accidentally?
If two ungrounded (hot) conductors touch or an ungrounded and a grounded (neutral) conductor accidentally touch, it is called a short or short circuit. If an ungrounded or a grounded conductor touch an equipment grounding conductor, it is called a ground fault.
Why does copper wire have to be insulated?
To stop the conductor from touching adjacent grounded structures.
What conductor should be grounded in a four wire three phase system?
The neutral.
What is the difference between a Grounded conductor and a Grounding conductor?
In residential 120 VAC, single-phase electrical wiring, there are three main types of electrical wires: 1. Ungrounded conductor (Hot, and sometimes called "Line" or "Phase") 2. Grounded conductor (Neutral), and 3. Grounding conductor (Safety Ground or Protective Earth) The groundED conductor is the power return, intended as a current return path from the load back to the source to complete the "circuit." Its insulation is White, gray or a non-green color with white stripes. The National Electric Code requires it be connected to earth ("groundED ") at the service entrance and usually only there. The groundING conductor is usually the safety ground which serves as an emergency current return path in the event of a circuit fault or overvoltage. Like the groundED conductor, it too is grounded at the service entrance, but is also connected to metal surfaces and parts along the circuit, groundING them. It conducts current only if the current "seeks" to return to the service entrance along a path other than the Neutral (like through your chest, should a Hot wire becomes loose and contact metal in the circuit that you may touch). Since the grounding conductor doesn't normally carry current, its cross-section is sometimes smaller than the groundED conductor's. The grounding conductor's insulation is green (no other conductors can have green insulation) though sometimes it is bare copper. Sometimes the steel metal conduit enclosing the Hot and Neutral acts as the grounding conductor.
What happens when there is no plastic coating on a electrical wire?
Nothing happens. The wire will still conduct electricity. An example of this is the overhead utility wiring. The insulation on a conductor is there strictly to keep the conductor from touching any thing that would ground the conductor. This grounding could be from another adjacent conductor or a grounded medium around the conductor. A grounded conductor will trip the over current protection and trip the circuit off line. Without an insulation on the wire multiple wires in a conduit could not be utilized.
Why is difficult to change a metallic conductor which is held with hands?
It is difficult to charge a metallic conductor that is held with hands because the charge generated will be grounded through our bodies.
Why is it difficult to charge a metallic conductor which is held with the hands?
generated will be grounded through our bodies, that cause of shock!
What is the difference between a phase to ground connection and a grounded wye connection?
A 'grounded-wye' connection describes a wye-connected supply, whose star-point (or common point) is grounded. This is essential in order to ensure stable phase voltages. I'm not sure what you mean by a 'grounded-phase' connection; if you mean a 'grounded-line' connection, then this is a short-circuit to ground from a line conductor.
Shock on a phase wire not on a neutral wire?
That's because the neutral is a grounded conductor.AnswerThe line (not 'phase'!) conductor has a potential of 230 V (Europe) or 120 V (North America) with respect to the neutral, which is earthed (grounded) at the supply panel.As you are more than likely 'earthed' (or 'grounded') by virtue of standing on it, this means that if you come into contact with a line conductor you will experience a potential difference of 230 V (or 120 V) between your point of contact with that line conductor and your point of contact with the earth, and you will receive a shock.However, as the neutral conductor is already at, or close to, earth potential, should you come into contact with the neutral conductor, you will experience no (or very little) potential difference, and receive no shock.
