0
Circuit parameters can be classified as:
1-- Active or Passive
2-- Linnear or Non-linnear
3-- Unilateral or Bilateral
4-- Lumped or Distributive
1-- Active or Passive:
Those circuit elements that supply energy to an energised circuit are called active circit elements. Eg.: Voltage source, current source,etc.
Note: It is important to note that dependent sources cannot be placed under this category as they depend on the value of current or voltage in any other branch of the network.
Passive circuit elements, on the other hand, are those elements that use up the energy supplied by the active sources and\or do not supply their own energy to the circuit.
Eg.: Resistor, capacitor, inductor, etc.
Note: It is important to note that a capacitor does store energy and also supplies it back to the circuit but this energy is not of its own, instead it's the energy supplied by some active component. Hence, it cannot be placed under the category of active circuit parameters.
Thus an energised network(or a circuit) consists of both active and passive elements.
2--
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is the r-parameters of transistor?
r parameter is resistance parameter
What are linear and nonlinear circuits?
Linear (Straight) circuit: An electronic circuit where the info sinusoidal flood of recurrence f give a stead state yield. This circuit take after ohms law and the estimation of electronic parts doesn't change with the level of voltage of current in the circuit. Non-Linear (Non direct) circuit: The circuit in which the parameters change as for current and voltage. The parameter esteem like resistance, capacitance, inductance, waveform, recurrence and so on, is not consistent. This circuit doesn't take after ohms law and the v-i attributes are not a straight line.
What is the desired target value for a parameter?
The target value of a parameter is the perimeter.
Briefly explain 'h-parameter model' for BJTs?
h-parameter used to find the input and output impedence of the two port network. suppose if u connect a high load at the output port then u should take care that no current from the device will attack the network, to determine that we should know what is the impedance of the circuit.
Different parameter passing methods with examples?
explain parameter passing methods c program
What is the power factor of a circuit containing only Xc?
what parameter stay the same in LCR circuit ?
H parameter equivalent circuit of transistor is valid for?
small signal operations
Why z parameters are called open circuit impedance?
In the Z-parameter Equations the independent parameters are Currents i.e., i/p And O/p . therefore to find any of the parameter(Z11,Z12,Z21,Z22) We have to either open circuit the input or the output port .as we are open circuiting any one of the port the Z-parameters Are called as open circuit parameters Got It ! Clear!
Is A query that prompts for input whenever it is run is a run-time query?
It is referred to as a parameter query.It is referred to as a parameter query.It is referred to as a parameter query.It is referred to as a parameter query.It is referred to as a parameter query.It is referred to as a parameter query.It is referred to as a parameter query.It is referred to as a parameter query.It is referred to as a parameter query.It is referred to as a parameter query.It is referred to as a parameter query.
What is a v out?
"Vout" typically refers to the output voltage of a circuit or device. It is the voltage level that is generated or present at the output terminal or node of the circuit. Voltage output is a common measurement parameter in electronics and electrical engineering.
Does electric current remain constant in a circuit?
No it depends on voltage and circuit resistance and other physical parameter which affect the properties of component used in circuitry like - temperature pressure humidity light(in light sensitive circuit- LDR photo diode,photo transistor,) and other.
What is the parameter of the Earth?
what is the parameter of earth
Why and when should programmers use a constant reference parameter?
when we use that parameter as a global parameter and we used that parameter through out the program without changing
What does parameter mean in science?
A parameter is something that limits something else. A parameter is a limit, or a boundary.
What is a parameter in maths?
A parameter is like a limit or a specification.
What does parameter passing in c means?
parameter passing in c, what does it do?
What is the r-parameters of transistor?
r parameter is resistance parameter
