0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Where is the sharder valve on dodge 3.9l v6?
There is no schrader valve on an 87 Dakota as it is carburated, other wise if its multiport fuel injection, on a 91 or newer model, it will be located at the end of the fuel rail under the valve stem cap.
How do I clean my pool filter?
If you have a cartridge filter simply take out the cartridge and hose it down and put if back together. If you have a sand filter stop the pump turn the multiport valve from filter to backwash, start the pump and run it until the water in the observation bubble runs clear, then stop the pump, now turn the multiport valve to rinse, and run the pump for about 45 seconds, and stop the pump again. Return the multiport valve to filter and you are done. if you have a DE filter go to the following link for a comprehensive U tube explanation. http://au.youtube.com/watch?v=jA-an54IVLc
What position does a multiport valve have to be on to vacuum a pool?
Should be set to Filter in normal circumstances, if particularly soiled, set to waste to save excessive dirt in filter.
How do you clean pool filters?
back-washing a sand filter sand filter with amultiport valve # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # start the pump # usually there is a clear bubble on or near the multiport valve. it shows the condition of the water. at first the water in it will look dirty when it clears up, turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 30 seconds seconds. # Turn off the pump then move the multiport valve handle to FILTER position # Turn pump back on and note lower pressure. ----Back washing a D.E. filter with a multiport valve; # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # Start the pump# Let the water run for 2 - 3 minutes or until it runs clear. Turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 5 to10 seconds. Turn of the pump.# Move the handle to BACKWASH. Turn on pump again until water runs clear. do this about 3 - 4 times, going from backwash to rinse, Backwash & Rinse, to ensure a thorough backwash. # Turn of the motor and move multiport valve handle back to the FILTER position # Turn pump back on# Add 1 lb D.E. powder per 10 sq ft of filter area. Check on the filter tank. ---- Cleaning a Cartridge filter # Turn of the pump # Open the air bleeder opened, # Remove the cover, # Remove the cartridge # Hose it thoroughly from top to bottom, until all of the debris stuck to it is gone # Soaking the cartridge in a TSP (trisodium-phosphate) or similar solution can be helpful especially with older filters that can suffer from blocked pores. NOTE Do not use TSP with Baquacil or Soft Swim for sanitation.----
Do you plug in a hose somewhere before setting to back wash an in ground pool?
Notnormally You may have to top up the water a bit because the back wash process tends to lower the water level of the pool a bit bit no hoses need to be plugged in anywhere as the backwash system is part of the filtration set up. Below I have put in backwash instructions---- back-washing a sand filter sand filter with amultiport valve # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # start the pump # usually there is a clear bubble on or near the multiport valve. it shows the condition of the water. at first the water in it will look dirty when it clears up, turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 30 seconds seconds. # Turn off the pump then move the multiport valve handle to FILTER position # Turn pump back on and note lower pressure. ----Back washing a D.E. filter with a multiport valve; # Turn of the pump# while pressing down on valve handle, turn it from the FILTER to the BACKWASH position # Start the pump# Let the water run for 2 - 3 minutes or until it runs clear. Turn of the pump.# Turn multiport valve handle to RINSE and Run it rinse for about 5 to10 seconds. Turn of the pump.# Move the handle to BACKWASH. Turn on pump again until water runs clear. do this about 3 - 4 times, going from backwash to rinse, Backwash & Rinse, to ensure a thorough backwash. # Turn of the motor and move multiport valve handle back to the FILTER position # Turn pump back on# Add 1 lb D.E. powder per 10 sq ft of filter area. Check on the filter tank. ----
How do we backwash sand filter?
Backwash a sand filter with a multiport valve; # turn off the pump motor # Start by Rrotating the handle on the multiport valve from the FILTER position to the BACKWASH position, Usually in the opposite direction) # Start the pump, Usually there is a clear bubble on the sand filter and you will see dirty water running through it, Wait until this water starts to run clear. otherwise keep an eye on the water exiting if you can until it runs clear. this can take about 2 to 4 minutes. # Shut off pump motor and move multiport valve handle to the RINSE position .Run on rinse for 15 - 30 seconds. once again you can keep an eye on the clear bubble to see the water clear if you have one. # Shut off pump motor again and move multiport valve handle back to the FILTER position # Now start pump again on and take note of the lower pressure. when the pressure gets too high again it is time to backwash once again.
Can be described as multiport bridges?
switches
What is a MPI?
MPI stands for multiport injection.
The top dial is missing which direction for filter the pool water?
This is (obviously) important, given that you could ruin your filter or send contaminated water back into your pool. Don't be cheap. Buy a new multiport valve.
What is an mfi fuel system?
MFI is an acronym for Multiport Fuel Injection. An MFI Fuel System is a fuel injection system that uses one injector per cylinder, mounted on the engine to spray fuel near the intake valve are or the combustion chamber.
What is the function of the recirculate position on a multiport valve?
Recirculate allows water to circulate through the system but bypasses the filter. This allows one to keep the pool water flowing, and components like a salt water chlorinator running, even if the filter is broken.
Where is the egr valve located on a Dodge Ram 1500 5.9L?
The 5.9L V8 only had egr in 1995 and before. It was located behind the intake next to the distributor on a multiport fuel injected engine, and on the side of the intake on a throttle body injected version.The 5.9L V8 only had egr in 1995 and before. It was located behind the intake next to the distributor on a multiport fuel injected engine, and on the side of the intake on a throttle body injected version.
