0
same, just invertment of each other
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Difference between jk flip-flop and t flip-flop?
in SR flip flop when we have S=1 R=1 we get intermediate state In JK flip flop we eliminate the intermediate state by complement Q- ( J=1,K=1 Q+ = (Q-)') so we can say that JK flip flop is refinement of SR flip flop Amjad Al.Haqpani
What is the effect of Rs and RL on the voltage gain of an amplifier?
it reduces the gain
How many rupees is electricity per unit?
Cost per unit of electricity depends the type of generation used. ie:- thermal hydel, nuclear etc. hydel electricity is cheaper and now a days it cost less than Rs.10 per unit in India. whereas thermal electricity cost less than Rs. 20 per unit
How designing stabilizing resistor in restricted earth fault relay?
To determine the value of Stabilizing resistor Rs = Vs/Is = If(Rct +2Rl)/Is Where, Rs = resistance value of the stabilizing resistor Vs = voltage at which the relay will operate Is = current flowing through the stabilizing resitor and the relay If = maximum secondary fault current magnitude Rct = internal resistance of the current transformer Rl = resistance of attached wire leads
What are the differences between GPIB vs rs232?
GPIB (general purpose interface bus) is a parallel port device. it can transmit more than one bit at a time. it is faster than rs 232 port. which is a serial port can transmit one bit at a time.the only disadvantage of GPIB or parallel port is it require more transmission bit so its transmission distance reduces.
What is RS flip flop?
The "RS" in RS flip flop stands for "Reset-Set". The RS flip flop has a Reset and a Set input. You can reset or set the flip flop as desired. Output state will be held based on whichever input was last asserted.
Is rs flip flop a bistable multivibrator?
yes it is
Define flip-flop.Explain about RS flip-flop?
flip-flop is a one bit memory device which stores the last output in memory. the output of flip-flop is based on the present input and past output. RS stands for reset-set flip-flop means that for particular value it sets and resets automatically based on inputs.
How is the j-k flip flop an improvement of r-s flip flop?
The JK flip-flop is not better than an RS flip-flop...it's just different. The selection of one or the other depends on what you are trying to do in your digital circuit design.
Difference between jk flip-flop and t flip-flop?
in SR flip flop when we have S=1 R=1 we get intermediate state In JK flip flop we eliminate the intermediate state by complement Q- ( J=1,K=1 Q+ = (Q-)') so we can say that JK flip flop is refinement of SR flip flop Amjad Al.Haqpani
What is a RS flip-flop?
two crosscoupled inverting gates form a Reset Set flipflop.
What are the five basic elements in a 555 timer IC?
Inverter, comparator, RS flip-flop, and transistor
Design 3 bit ripple counter using JK flip flops?
I am not a Electronic Engineer, so probably any expert out there can correct me if I am thinking wrong.--------- As you can see below there is something common between JK and SR flipflop i.eThe JK flip-flop augments the behavior of the SR flip-flop by interpreting the S = R = 1 condition as a "flip" or toggle command. Specifically, the combination J = 1, K = 0 is a command to set the flip-flop; the combination J = 0, K = 1 is a command to reset the flip-flop; and the combination J = K = 1 is a command to toggle the flip-flop, i.e., change its output to the logical complement of its current value. Setting J = K = 0 does NOT result in a D flip-flop, but rather, will hold the current state. To synthesize a D flip-flop, simply set K equal to the complement of J. The JK flip-flop is therefore a universal flip-flop, because it can be configured to work as an SR flip-flop, a D flip-flop or a T flip-flop. NOTE: The flip flop is positive edge triggered (Clock Pulse) as seen in the timing diagram.even in the picture they Put SR/RS embeded, that mens JK can work like SR too. I will use this diagram to draw ripple counter. You may note similarity in input output combination too...RS table* We can summarize the operation of the RS-flipflop by the following truth table.R S Q Q' Comment 0 0 Q Q' Hold state 0 1 1 0 Set 1 0 0 1 Reset 1 1 ? ? AvoidJktableand the corresponding truth table is: J KQnext Comment 0 0 hold state 0 1 reset 1 0 set 1 1 toggleDoes that mean we use below coutner 'using 4 bit ripple counter using JK flip flops' as 4 bit ripple counter for RS flip flop too? at the max output states would differ only when both SR/JK is 1 1 ?Figure 1. A Simple Ripple Counter Consisting of J-K Flip-flopsMethod1: You will find answer here: http://www2.cs.uh.edu/~jhuang/JCH/LD/chap07.htmlHere you see how to create ripple counter using RS flip flop. Method 2: create a Toggle function in RS flip flop, then use it in place of typical jk flip flop ripple couters.
What is the full form of j-k in j-k flipflop?
Actually, the choice of the letters "JK" in the JK flip flop do have significance. The JK flip flop was named after Jack Kilby, the Texas Instruments engineer that invented the integrated circuit in 1958. The modified RS circuit that eliminated race conditions was named JK in his honor. Search for "JK" and "Jack Kilby" simultaneously to see multiple sources for this.
What is the difference between the currency of India and Australia?
rs.100
What do you need for an electronic one button switch?
a one button switch feeding maybe an rs flip flop so the contact bounce wont cause a computer to think you pushed the button 20 times instead of once
What is the difference between eclipse gt and rs eclipse?
http://en.wikipedia.org/wiki/Mitsubishi_Eclipse
