answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered 2014-11-20 03:33:58

For a Fort F250 from 1986, most vehicles have a recommended torque of 140 foot-pounds. This has increased for later models of F250, to a current 160 foot-pounds.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

What are the torque specs for a 1986 small block Chevy cylender head?

65ft. LBS.


What are the cylinder head torque specs on a Oldsmobile 3.1 liter?

what are the head tourque specs for a 1986 Oldsmobile calais 2.5 liter ?


What is torque specs for head bolts on 1986 Chevy 305?

75 lbs--rods 45 lbs


What are the torque specs for 1986 Honda trx200sx for the cam bolts and cylinder head?

25-35 ftlbs


Does anyone have torque specs for your 1986 Nissan 300zx thermostat cover bolts?

The bolts have a number on it, what is the number? There is a general torque spec in the shop manual that will say what the torque is based on that number


What are the specs for a 1986 Monte Carlo SS with a 305 V8 engine?

190 horsepower 240 pound torque


What are the torque specs for the head bolts on a 1986 Chevy 350?

torque, in sequence, to 35-40 ft-lbs, then repeat at 65-70 ft-lbs in sequence.


Torque specs intake manifold olds 1986 cutlass 307?

Cast iron intake is 30 lb/ft


What is the correct 1986 Chevy van wheel torque in Nm's?

Astro and Safari 100 ft. lbs.


What is the head bolt torque and tightening pattern for an 1986 Mitsubishi Mighty Max Pick-up Truck 2.0?

The cylinder head bolt torque specs for a Mitsubishi 2.0 or 2.6 is 65 to 72 ft. lbs. cold. Torque sequence is as follows.


What are the torque specs for the head bolts of a 1986 Mazda B2000?

For the 1998cc, from the AllData manual "copy": 80-86 N-m (59-64 ft-lb).


Rocker arm torq specs 1986 dodge d 100?

All of the torque specifications for vehicles can be found in Haynes Repair Manuals available at most auto parts stores.


What are the torque specs and order of tightenig on a 1986 350 Chevy intake manifold?

Cast iron heads are 30 lb/ft of torque. There is no sequence. Just tighten them all down very slowly in a criss cross pattern. In other words all at the same time.


What are the valve lash specs of a 1986 Mazda B2000?

0.012


How hard is it to replace the torque converter seal on a 1986 ford ranger 4x4?

All you have to do is take the tranny out and unbolt it from the fly wheel, its really easy, I have done it a few times.


How much horsepower and torque does a 1986 corvette have?

230 hp/345 ft lbs of torque


Connecting rod torque for a 22r?

1986 is 43lbs


What is the torque for an 1986 Dodge 318 rod bearing bolts?

the correct torque for these bolts is as follows: 96lbs


What are the torque settings for Nissan micra 1986 1.2?

what are the torque settings for a1986 Nissan micra please.


What is the torque specs for the front axle on an 1986 Honda Goldwing?

Torque spec's front axel nut is 44 ft-lb caliper upper bolt 25 ft-lb and lower bolt is 17 ft-lb..............Tighten the axel holder forward nuts first, then the rear nuts. Torque is 18 ft-lb. There you go, right from the book. Good luck.


What is head bolt torque on 1986 corvette?

The head bolt torque specifications for the 1986 Chevrolet Corvette is 200 pounds per square inch. The bolts should be torqued at 50 pound intervals.


Is the 1986 fiero real wheel drive?

Yes , it's rear wheel drive


What are the specs for valve adjustment on a 1986 Mazda B2200?

Who is a valve calibration for mazda b2200 1988


What are the correct specs on a 1986 radiator cap?

Not knowing what vehicle, 15 psi is probably average.


Are 1986 camaros rear wheel drive?

Yes


Still have questions?