The alternator is driven by the drive belt. Find the belt and follow the routing and you will find the alternator.
You have to remove the power steering belt and the AC belt to remove the alternator belt.
Loosen the tensioner pulley. The alternator belt will come loose. Remove the alternator belt. Put the new alternator belt on and tighten the tensioner pulley.
Need alternator belt routing on XC70 2003 Volvo
locate the alternator take off the belt put new one on then the belt and your done
There are no 1996 stanzas
Remove the neg battery cab;e then the wires on the alternator.. Disengage the belt and take the mounting bolts out of the alternator. There should be a routing schematic for the belt on the fan shroud.
Remove the wiring harness from the back of your 1989 Toyota alternator. Remove the alternator retaining bolts. Remove the alternator belt. Reverse the process to install the new alternator.
You can replace the alternator on your 1989 Mercury Cougar by removing the alternator belt. Disconnect the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.
there is a belt tensioner near the alternator.
Save the radio codes. Write them down if required. Disconnect the positive lead of the battery. Disconnect and mark or take a closeup picture of the leads on the back of the alternator. Loosen the alternator belt, note the belt routing, and draw a picture if needed. Slip belt off alternator pulley and remove mounting bolts on alternator. Lift alternator out of unit.
Begin by removing the alternator belt on your 1989 Chevy Corsica. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install the new alternator.
The alternator is usally on an adjustable slide mounted to the engine. If you adjust the alternator on that slide to take the tension off the belt you should be good to go to put the new belt on. The routing diagram for routing the serpentine belt should be on a placard mounted under the hood on the frame. It should also be in your user's/maintenance manual. Make sure to adjust the alternator properly on its slide mount so that there is sufficient tension in the belt.
Serpentine belt See "Related Questions" below for more about Windstar serpentine belts - routing & installation information.
most vehicles have the belt routing under the hood if this is no longer available some auto part stores have a manual [book] that will show this
The alternator tell, can be replaced by loosening the tensioner pulley. With the tensioner pulley loose the belt will easily come off and can be replaced.
loosen the alternator and it will slide right off Check 2carpros.com for a belt routing diagram.
most auto parts dealers have or can print out a routing diagram.
Loosen the alternator tensioner bolt. The alternator belt will become loose. Remove the alternator belt. Put the new alternator belt on and reverse the process.
alternator drive belt?
Yes, I know of no engine where the alternator is driven by the cam belt. The alternator is driven by a drive belt or serpentine belt.
How do I put a alternotor belt on a 1991 Acura Legend
You dont need a diagram.. just trace the route with the eye.. Besides.. if your going to change the alternator belt.. you might as well change all 3 if its on the V6.. Oh.. and is a PIA job..
Assuming you have a 91 to 02 LX with AC, power steering and alternator the belt starting with the tensioner on top then it goes clockwise to the alternator, power steering, idler pulley, A/C, crankshaft pulley---------back to the tensioner.
My 98 Stratus has two belts, on for the power steering and the other is the alternator belt. To get access to the belt a cover over the alternator must be remove. A 10mm socket on an extension is useful. Remove the old belt loosen the mounting bolts for the alternator and loosen the tensioning bolt. This bolt is mounted on the side of the alternator, facing the front of the car. Take note of the routing and check the underside of the hood for a diagram of the routing. Slide the old belt off the idler and remove then replace the new belt on in the same fashion. Note: the Dodge Stratus has a cover under vechile covering the belt and oil pan. I found it extremly useful to remove this cove to have access to the AC compressor and CrankShaft. Don't forget to tighten the belt using the alternator adjusting screw. Good Luck!