0
What is the best way to remve and replace the spark plugs on the firewall side of the engine?
Wiki User
∙ 15y ago
I changed mine on a 92 Lesabre and even though it is a tight space I used a special spark plug socket and rachet and had very little problem. Make sure you don't cross thread the new plugs and make sure your wires are put on properly and you should be ok.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you change spark plugs on a 2000 Mitsubishi diamante?
you have to remve the intake manifold
Replace brake light bulb on 1997 Chevy silverado 3500?
remve the tail light they are on the back side.
How do you change spark plugs on a 1997 Dodge Neon?
simply pull on the spark plug wires, after removing engine cover of corse. then get a rachet exstention connected to your rachet, find the correct rachet size, place it in the the spark plug holes loosen all the way, remve rachet and then put the long plugs back in the holes intil the click back on the plugs pull up and repeat proseess
How do you take the motor out of a 2006 ford with a V-10 engine?
to take engine out of a 2006 ford, the cab has to be romoved first why on earth ford came up withat dumb idea has got me beat pretty much all ford pickups from 2000 on have to remve cab
Where does the hose that comes out of the back of the water pump go and how do you replace it when it leaks?
I had to look at this question for a minute because you didn't say what year model we are working on or what engine size. But I guess we must have a 1996 or newer model, and we must be working on a 4.6 liter engine. If I am right about what we are working on, the bypass hose you have described, goes through a valley under the intake manifold, and exits at the rear of the engine, where it connects to a heater hose at the firewall. It is partly rubber hose and partly metal pipe, but it is made as one assembly. To access and replace, you must remove the intake manifold. After the intake manifold is moved out of the way you will see it clearly. At the back of the engine, on the right cylinder head, there are two bolts that hold it to the back of the head. There is also a bracket that is held to those bolts by two nuts that are screwed to threaded studs that are part of each bolt, so that you have to remaove the nuts, remve the bracket, then remove the studded bolts, and then remove the bypass hose/pipe assembly, all of this after you have removed the intake manifold.
Can you replace the batteries in your blue parrot headset?
Yes you can replace the battery in the Blue parott headset. Just remve the two small Phillips head screws and lift off the cover. Then unpug the two wire connector (that is pluged into a circuit board.) to remove the old battery, then do the reverse to install the new battery. Much easier than it sounds.
How do you remve drum on sw 38 spl model 60?
You can get a owner's manual for free at the S&W web site.
How do you replace a motor mount in a 1985 Dodge Ram?
very easy, go under the truck, take off both nuts for the mounts, go up top and remve 2 more nuts, 1 per side. jack up motor, and ta da ! presto chango.
How do you get permanent marker off of concrete?
My little sister wrote in black ink permanet marker in the parking lot concret and we don't know how to remve it...can you help me?
How do you change the rear brake pads on a 2002 dodge ram 1500?
jack up vehicle. remove wheel remve caliper bolts from rear of caliper slide caliper off rotor remove old pads push piston back into caliper with a c clamp insert new pads reinstall calipers and bolts replace wheels
Where is the blower resistor on a 1999 Contour?
The blower motor resistor is located on the passenger side under the glove box. Left side. there is a cover on the blower motor. remve the cover, this is the resistor. there is an electrical plug there.
How do you change the optispark on a 1994 camaro Z28 LT1?
very big job. the water pump must be first removed. you will need a t-8 torx bit for the rotor removal and a e-4 torx socket(reverse torx) drain coolant. remove serpentine belt. you may have to take out the electric fan. I did it without removing it but it was tighter. remove hoses from water pump. disconnect coolant sensor and unclip it from top of water pump. unbolt ignition coil bracket. unbolt and move airinjection pump. remve the 2 bolts holding the air injection pump bracket. remve water pump bolts and then the pump. remove the harmonic balancer pulley keeping note of the position of the arrow on said pulley.remove plug wires. remove the dist cap. remove rotor and replace it with new one in same position. replace with new cap and then reverse steps.
