0
It varies depending on the country your in, the voltage of the cable and the type of soil. Also if there is anything on the surface above the cable, railway lines for example. Another important thing to remember is that not all 'time-is-money' cable laying crews follow the rules. From experience, they are almost always too shallow. Scary!
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
What is the minimum depth that cables should be installed in walls before protection is necessary?
50mm. The rule of thumb is, place the hole in the center of the stud. At this depth no drywall screws or nails will reach the cable.
Three examples of good practice when installing cable runs?
Cables should not come into contact with metal work or polystyrene. Should always make sure are not crossing or tangled. Cables must be installed at the right depth.
Can you give me a good sentence for underground?
A spirit raised from depth of underground.
What are uses of armoured cables?
Armored cables are generally used to protect cables from mechanical damage, normally when they are buried.One of the first uses of armored cable was actually the trans-Atlantic telegraph line between the UK and US. This was a sea cable that had to withstand the pressures of the depth as well as support its own free weight during installation. Additionally it had to protect the telegraph wire inside from mechanical abrasion against rocks due to underwater currents.More commonly nowadays, these types of cable are used to protect high and low voltage subterranean power cables and fiber optic cables
What precautions should be taken in laying power cables in an underground trench?
Before digging the trench, make sure there are no lines or cables under that ground. In rural areas there should be no problems. However, in urban areas it would be advisable to call MISS DIG. Be sure that the cable is in some kind of water-tight conduit or pipe, dug to proper depth, and clean sand or pea stone is placed around the pipe to protect it.
Depth of laying optical fiber cables?
100 cm
What should be considered when choosing the length of an anchor cable?
The depth of the water should be considered when choosing the length of an anchor cable. The anchor cable needs to be 4 to 7 times longer then the depth of the water.
Is there a specific depth for underground oil lines from your oil tank to your heater?
500mm
How does the Breslow system measure the depth of a malignant melanoma?
The Breslow system uses the absolute measurement of depth.
How far underground is Lightning Ridge?
The town of Lightning Ridge is above ground. Only the opal mine shafts go underground, and these vary in depth.
Depth of cable tv cables?
Usually below the 'frost line' in most areas, or from four to six feet, on the average. But if you're going to be doing any digging, call first so they can come out and mark where it is. There's usually a 'call before you dig' number in your phone book.
What problems should be paid attention to when laying photovoltaic cables?
Cable laying The cable laying method is comprehensively considered according to factors such as engineering conditions, environmental conditions, and cable specifications, models, and quantities. The selection of the cable needs to be selected according to the principle of satisfying the requirements of reliable operation, easy maintenance, and reasonable technology and economy. There is little difference between the laying of AC cables and the laying of general power systems. DC cables are mostly used between photovoltaic modules, between strings and DC combiner boxes, and between combiner boxes and inverters. The cross-sectional area is small and the number is large. Generally, the cables are bundled along with the module brackets or laid directly through pipes. , DC cables generally need to be considered when laying: Connecting cables between components and connecting cables between strings and combiner boxes. As far as possible, use component brackets as channel support and fixation for cable laying, which can reduce the effect of environmental factors to a certain extent. The force of the cable laying should be even and appropriate, and not too tight. The temperature difference between day and night is generally large in the photovoltaic site, and thermal expansion and contraction should be avoided to cause the cable to break. For the cable leads of photovoltaic materials on the surface of the building, the overall aesthetics of the building should be considered. The laying position should avoid laying the cables on the sharp edges of the walls and brackets to avoid cutting, abrading, and damaging the insulation layer and causing short circuits or cutting the wires by shearing force. Cause an open circuit. At the same time, it is necessary to consider issues such as direct lightning strikes on the cable line. Reasonably plan the cable laying path, reduce the crossing, and combine the laying as much as possible to reduce the amount of earth excavation and the number of cables during the construction of the project. Cable construction costs in photovoltaic power generation projects are generally relatively large, and the choice of laying methods directly affects the construction costs. Therefore, reasonable planning and the correct selection of cables are important aspects of photovoltaic construction. KUKA CABLE through in-depth research on the laying environment, technical parameters, application occasions, etc. of cables for photovoltaic power generation systems, provides system selection and optimization schemes and conducts research and development and design of new products to create a complete building/water surface/centralized photovoltaic The overall product solution.
