Distributors and Distributor Caps
Timing and Firing Orders
Chevy Corsica
Chevy S-10

What is the firing order for a Chevy Corsica 3.1L V6?

8910

Top Answer
User Avatar
Wiki User
Answered
2005-11-03 06:02:54
2005-11-03 06:02:54

seriously it is 1-2-3-4-5-6 for all v-6 engines in the berreta or corsica wolverine

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


123456 is the firing order from the GM HAYNES REPAIR MANUEL

there are 3 in the front and 3 in the back of the motor near the fire wall

Does it have a miss? check plugs and wires. Also a possibility of a bad throttle position sensor.

http://wiki.answers.com/Q/What_is_the_push-rod_placement_for_a_1996_lumina_3.1_engine

31L is 310 deciliters.

All O2 sensors are located on the exhaust system. Start at the exhaust manifold and work your way backward, and count them.

depends on the age and quality

http://wiki.answers.com/Q/Where_is_the_radiator_fan_switch_on_an_1995_olds_cutlass_31L"

No, I just recently was on a CRJ-900 that took off 31L.

You can remove the throttle body. It is then so much easier to get to the bolts for the thermostat housing.

Runway 13R/31L = 14,572 ft 13L/31R = 10,000 ft 4L/22R = 11,351 ft 4R/22L = 8,400 ft

You probably switched tow or more of the wires and cylinders. I did that exact same thing to a friends 98 Monte Carlo and it just sat there. go through the manual and make sure your wires all match and make sure next do the wire one at a time. one wire comes off;replace that exact same wire. and so on. i hope this helps. RC

The best way to find out is go to your local auto parts store, ask for a haynes or chiltons manual on your vehicle. This will tell you everything you need to know about working on your vehicle.

The original runways (that I know of) are: 1L 7L 31R (8000ft at the time) 31L (9500ft) 1R (Closed in the 50s) 7R (Closed in the 60s) 4 (8000ft now 4L, 1949) 4R (Added 1959)

the fuel pump is located in the fuel tank witch is located under the car in front of the rear axel. fairly easy to replace. if u can take it apart u can put it back together

the torque converter clutch soelinoid needs to be replaced.your computer should have a trouble code.(tcc.error-###) it is labor intensive repair and should be serviced by seasoned mechanic.

This is the Length to Weight Ratio ie: (Balance Point). Example: A 31L /21oz would be 31 inches long and 21 ounces in weight. The higher the negative number the lighter the bat is (for quicker bat speed).

I have a 92 lumina with a 3.1 and I found the crank sensor to be located on the passenger side of the engine in the back of the engine NOT on the side of the engine below the knock sensor. Hello, in my experience, all O2 sensors are located in the exhaust just after the manifold. It appears easy enough to change. If it is the crank position sensor you are looking for, take a look around the main pulley at the bottom of the engine, you may see a square-ish component located close to the actual pulley wheel, this would be the crank position sensor, it should have wires connected to it.

The #1 cylinder on 90 to 93 3.1L engines is on the rear towards firewall (passenger side) on 86-89 models it is on front, towards radiator (passenger side). *The cylinders are numbered 1-3-5 left to right on the back of the engine and 2-4-6 left to right at the front.

Check to see if the thermostat is stuck open also check for binding brakes.dirty or clogged fuel injectors. Also check the air filter.

Nice problem !At first, I thought you can't tell, because the perimeter doesn't tell you the area,so you can't tell what the original area is. But then I tried a few, and discoveredthat although you can't tell the original area or the new area, the increase is alwaysthe same ... 66 square centimeters.Let's see if I can prove it:Perimeter = 2L + 2W = 62L + W = 31W = 31 - LOld area = L x W = L (31 - L) = 31L - L2New area = (L + 2) x (W + 2) = (L + 2) x (33 - L) = 33L - L2 + 66 - 2L = 31L - L2 + 66 = Old area + 66Well that wasn't so bad.

The best way to find out is go to your local auto parts store, ask for a haynes or chiltons manual on your vehicle. This will tell you everything you need to know about working on your vehicle. It is a delicate job, make sure nothing falls into the motor & use the proper torque specs & sequence on your bolts otherwise you will crack or warp the aluminum manifolds.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.