0
What is the proper wire connection for a starter solenoid on a 1981 Olds Regency?
Wiki User
∙ 17y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you change a starter solenoid on a 1983 Chevy silverado?
I DO BELIEVE THE SOLENOID IS MOUNTED ON THE STARTER AND YOU WOULD HAVE TO REPLACE THE STARTER TO REPLACE THE SOLENOID remove the starter and take it down to your local auto parts store. they can bench test the starter and give you the proper solenoid if it needs to be replaced.
Where is the solenoid wire on a 1996 dodge stratus 5 speed?
Dodges and Chryslers mayby Plymouths also use a thick brown wire from the statrer relay in the fuse box. There should be two clicks by statring. Solenoid a louder and a relay a softer click. It is possible for the relay to click but its electical connection pole points might be corroded at the solenoid or the relay at the fuse box make sure that the brown wire from the relay to the starter solenoid is connected at the solenoid cleanly and tightly. If you always hear the loud click however, then you know the solenoid is getting the current from the relay and it is not applying the high current to the starter motor windings or the windings or brushes in the motor are bad, or the wire that brings the high current directly from the battery to the solenoid is loose at the solenoid. So when you find the starter make sure that the thick battery wire connection to the solenoid is clean and tight, and if it nonetheless clicks then there is indeed a problem internally with the solenoid switch or the motor proper. You can also bypass the solenoid and see if the starter cranks, to see if a problem at the solenoid.
What would cause a solenoid to go bad in a month repeatedly?
Perhaps a loose connection causing excessive resistance. Check ground connection also Solenoid not of proper rating (too light to carry load)
What is the proper placement of wires on the starter solenoid of a Ford E-150 van?
if your standing above the solenoid the wire to the stater goes on the left all other wires go on the right
Why would a 1999 Chrysler Concorde just click even if the battery is fully charged?
Sometimes it's just a matter of a good connection you need to make sure you have good clean connections at all points coming from the battery, make sure the terminals are clean and tight if there is any corrosion between the battery post and the terminals you want get the proper amount of power going to the starter solenoid to kick in the starter and that's were you hear the click that's the solenoid trying to kick in.
What is the proper placement of the wires on the starter solenoid of a 1983 Ford Thunderbird?
Looking at the solenoid from the front, and working towards the left, the right terminal will have one wire that goes down to the starter. The little push-on wire (usually red) will be the one that goes next. There may be another little push on, or a couple of wires with terminals- they all get attached to the next small terminal. The last terminal on the left of the solenoid is where the battery wire, and any other accessory wires go.
Why does your jet ski only start when you jump the ignition selenoid?
The most likely explanation is that the solenoid itself has failed. The next most likely explanation is that the wiring to the ignition solenoid is not making proper contact or there's a bad ground connection. The least likely explanation is that the electronics that control the ignition solenoid (MPEM or whatever it's called on your model) is broken.
What is the proper wiring for a 2000 Chevy impala 3.4L starter?
what is the proper way to wire the starter for a 2000 chevy impala
Why do you have trouble starting the car though d battery and alternator are ok and there are no sounds to be heard upon turning the key however it works based on luck?
Starting FailuresYour question is confusing, "...based on luck?"I suspect that you mean that the problem is intermittent [sometimes it works when you turn the key to the start position, and sometimes it doesn't.IF that's the case I suspect one, or a combination, of the following:A "loose" connection somewhere in the starter/solenoid circuit,A defective starter solenoid,A defective starter,A defective starter/ignition switch.NO ONE can tell you precisely what the cause is without "troubleshooting" the entire starting system, but the above causes can result in the symptoms you describe.You need to have someone who knows what they are doing to troubleshoot your starting system, find and identify the cause(s), and make proper repairs.
What is a proper way to connect a second starter wire?
The proper way to connect a second starter wire depends with the configuration used.
Your 1995 Ford Aspire won't turn over you went start it clicked and now will not start could it be the starter or the ignition switch?
Please make sure the battery is fully charged before doing this test! Also make sure all the connections on the starter, battery and cable ends are tight and clean! this is important!! This won't be fun to test but it will tell you if the starter is good or not. Crawl under the car. (Make sure you use the proper jacks and jack stands!) find the end of the starter (not the end that is attached to the bell housing) and find the solenoid switch. it should have 3 bolts on it. Two large ones and a small one. The top large wire should be the positive battery cable, the bottom large wire should go into the starter and the small wire should be from the ignition switch. Take a wire and hold it to the top large wire on the solenoid. (be careful of the other end of that wire when you have it connected to the top large wire of the solenoid! don't ground this wire. it will turn out badly. don't ask me how I know this is true!) take the other end of the wire and touch it to the small bolt on the solenoid end. If the starter is working, the solenoid should engage and the starter will turn. If this happens it is most likely the ignition switch. If the starter doesn't turn, the starter could be bad.
How do you replace the starter in a 1993 jeep Cherokee?
Chock the wheels, disconnect the negative battery cable.. you might need to lift the front end and put the vehicle on jack stands... It's a pretty straightforward process. You remove the wires from the starter and starter solenoid, and make note of which wires go where. Wires clustered together should be taped together. The starter itself will typically be three or four bolts.. unbolt them, and the starter comes right out... look on the front of the flywheel... IIRC, they're located on the right side on that model. Installation is the opposite of reverse... ensure a proper fit, proper operation when you install the new starter and reconnect the battery... adding shims might be necessary to ensure proper alignment of the bendix and the flywheel.
