0
What is the route of the output shaft speed sensor circuit in 1999 dodge 1500 ram?
Wiki User
∙ 8y ago
The output speed sensor circuit runs from the sensor, on the driver side of the transmission, to the engine computer. The computer is under the hood on the passenger side firewall.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
What is the name for a circuit with one route around it?
Series Circuit
Can you show me a diagram showing where I should route the crankshaft position sensor cable in a 2000 eclipse GT with 3L?
2000 dodge Dakota camshaft sensors location
Short circuits are dangerous because?
electricity always "wants" to take the easiest route, this is the route with the least resistance, this is why an insulator does not conduct electricity, it takes to much force for the electricity to travel through. a short circuit is when the easiest route is the wrong route i.e. the body of a lamp rather than the wiring of the lamp. the danger of a short circuit is dependent on the voltage and current of the electricity.
What path allows only one route for an electric current?
It is series circuit
Multiplier is also know as data selector why?
A multiplier is a digital circuit that performs multiplication of two numbers. It is not typically referred to as a data selector. A data selector, also known as a multiplexer, is a digital circuit that selects one of several inputs and routes it to the output. It is called a data selector because it selects which data input to use and sends it to the output. A data selector has several inputs and a single output, and it is controlled by a set of select signals that determine which input to route to the output. The data selector is used to choose between multiple inputs and can be used to implement functions such as Boolean logic or arithmetic operations. In summary, a multiplier is a circuit that performs multiplication, while a data selector is a circuit that selects one of several inputs and routes it to the output. These are two different types of digital circuits that serve different functions.
What is a single route for electrical current called?
A single route for electrical current is called a branch circuit.
Route for serpentine belt on 1994 Dodge Spirit?
serpentine belt routing diagram for 1994 dodge spirit
What is the error code P1762 on a 1997 ram van 2500?
There is a whole list of testing procedures but you need a DRBII scan tool to do the tests. SYMPTOM P1762-GOVERNOR PRESSURE SENSOR OFFSET VOLTS TOO LOW OR HIGH WHEN MONITORED Continuously with the key ON and the engine running. SET CONDITION This code will set if the governor pressure is out of range in park or neutral for 1.3 seconds for three consecutive bad 3.0 second tests and sump temperature > 10 �C (50 �F) and < 127 �C (260 �F) are required to set the code. POSSIBLE CAUSES Powertrain control module Powertrain control module - 5 volt supply high Powertrain control module - after 5 volt supply shorted to voltage Powertrain control module - after 5 volt supply shorted to voltage in trans Repair the 5 volt supply circuit and check the PCM Replace the trans solenoid assembly and check the PCM Intermittent condition Powertrain control module - internal fault 5 volt supply circuit open Check for other trans DTC's Governor pressure sensor signal circuit shorted to voltage inside trans Check trans fluid level and condition Governor pressure sensor signal circuit shorted to voltage Park neutral DTC present 5 volt supply circuit shorted to ground Governor pressure sensor signal circuit shorted to 5 volt supply circuit Governor pressure sensor signal circuit shorted to 5 volt supply circuit inside trans Governor pressure sensor signal circuit shorted to ground 5 volt supply circuit shorted to sensor ground Governor pressure sensor signal circuit open inside trans Governor pressure sensor signal circuit shorted to sensor ground GOV pressure sensor signal circuit open Governor pressure solenoid Governor pressure sensor signal circuit shorted to ground inside trans Powertrain control module - 5 volt supply circuit low Sensor ground circuit open Transmission line pressure low Governor pressure sensor signal circuit shorted to sensor ground inside trans 5 volt supply circuit open inside trans 5 volt supply circuit shorted to ground inside trans 5 volt supply circuit shorted to sensor ground inside trans Sensor ground circuit open inside trans Governor pressure sensor Copyright � 2002 ALLDATA LLC That means you go to your local Dodge dealer, grab the Governor Pressure Solenoid, Transducer, 2 gallons of Mopar ATF, a filter, and gasket and change them out. It takes about 1 hour total to do the job in your driveway. YOU DO NOT HAVE TO REMOVE THE VALVE BODY Once the pan is dropped and the filter is removed you will notice the wiring laced threw-out the valve body. These lead to your GPS and Transducer solenoid. I didn't want to go the dealer route and pay big bucks for the Governor Pressure sensor and Governor Pressure solenoid. With a little online searching I found Transtar Industries, Inc. at www.transtarindustries.com Part numbers where 20A-120A for the sensor and 5A-303 for the solenoid. The prices quoted me were just over $120 for both parts. This was $100s better than what the dealer quoted me. This was for a 1997 46RE transmission. Also applies to the 47RE trans. MRinfinit3 Jake- ASE Master Certified Tech. 2008
What is the Least Crowded Route on Kilimanjaro?
The least crowded route on Kilimanjaro is often considered to be the Northern Circuit Route. This route is relatively new and less frequented compared to other popular routes such as the Marangu, Machame, and Lemosho routes. The Northern Circuit Route offers a longer trek and a more gradual ascent, providing better acclimatization and increasing the chances of successfully reaching the summit.
A path that allows only one route for a current is called a?
series circuit
A path that allows only one route for an electric current is what?
A series circuit.
How do you make a circuit bigger?
It depends on what circuit you have in mind and what tools you have. If you wish to expand an existing DC or low frequency circuit, you can add jumper wires and route them to an expansion board where the rest of your circuit may be built.
