Starters and Ignition Systems
Chevy S-10
Chevy 305
Crankshaft Sensors

What is the sensor on a 305 Chevy motor right next to the starter?

596061

Top Answer
User Avatar
Wiki User
Answered
2005-05-19 02:55:39
2005-05-19 02:55:39

it is a knock sensor that is used to adjust the ignition timing.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The crankshaft position sensor is located right above the starter, you may have to remove the starter for better visibility.

It's easy its just above the starter remove the starter with 1/2" socket your crank sensor is right there one 10mm socket

setting in the seat, It will be on the right side of the engine.

It is right behind the starter and bolted into the side of the engine block. You will have to remove the starter to service it.

It is mounted in the passenger side of the engine block right behind the starter. You will have to remove the starter to get to it.

right in thr front underneath the car on the right side of the oil filiter

It is bolted in the side of the engine block right BEHIND the starter. You will have to remove the starter to see are to even get to it.

It is bolted in the passenger side of the engine block RIGHT BEHIND the starter. You can not see or get to it untill you remove the starter.

You can find the starter on the right hand side of the motor. The starter will be near the back of the motor. You can follow the positive battery cable to the starter.

on the right of your PC valve Where is the PC valve?

at the bottom rear underside of the motor, right beside the oil pan.

I just replaced the starter motor on my 1990 4 cylinder engine Chevy Lumina. The starter is located in front of the oil pan. It was reachable and can be seen from under the front of the car a little to the right. You have to remove a three bolt attached plastic part by the oil pan to be able to get to one of the starter motor bolts. Good luck.

You need to disconnect your battery cables. On the right side under your motor is your starter you will have a - and a + wire disconnect them then take off two bolts and your starter will come right off. Then assemble the way you took it off.

ON FRONT OF RIGHT CYLINDER HEAD, NEAR BREAKOUT TO STARTER MOTOR.

The starter motor is located at the back of the cylinder block on the right hand side

It is located right above the starter for a 5.7l V8, not sure for the 4.3 or 5.0, probably the same place

on the fender passenger side. If I remember right. disconnect batt. first, good luck. Your car has a starter solenoid rather than a relay. It is located piggy-back on the starter. It should be right on top of the starter motor, attatched.

You will fine it right on side of the starter on the front side of the motor

The crankshaft sensor is right next to the starter on a 2002 Escalade. You will have to loosen up the starter to get to it.

It should be on the right side of the motor by the oil pan looking at it from the bottom held in by two bolts

most small blick chevys have the oil sensor on the back of the motor behind the intake just right of the distributor

Right above the starter, but you'll have to first drop the starter to get access to the CPSensor. my son in law has a 99 suburban 5.7 and the crank sensor is located on the passenger side of engine at the front by the timing chain cover.

take the right back motor mount off then jack up the exgshast then the starter should come right out with a little moving around

the map sensor is located on the firewall to the right of the blower motor a small square box with two screws 2 minute job.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.